The filter head broke because it was designed wrong.
Shipping was very fast, part easy to install. The new filter head was redesigned making it easer to remove the filter. Loosen the two screws and remove bracket. Push in the tubing retainers and pull out the tubes. Remove the two screws holding the filter on to the bracket. Push tubing in to the fittings on the new filter head, pull out the tubing retainers about 1/16 in. Make sure tubing is pushed all the way to the bottom of the fitting. Reinstall bracket and filter head.
First I unplugged the refrigerater and turned off the water and disconnected the water line. I then removed the two screws that hold the element in place, pulled the element out about 3 inches and disconnected the two wires. Then I disconnected the two water hoses, replaced the old valve with the new one and proceeded to connect the water lines and the electrical connections, screwed the element back into place connected the water feed, and connected the electrical line and everything works!
While ordering the assembly, I had thought that the ice bucket was included but it wasn't. So I ordered the ice bucket afterwards. Maybe a little more clarity as far as what parts come in the whole assembly would save some time. All in all, the agitator was very easy to install, along with the ice bucket. After securing the agitator to the existing assembly with two screws, the ice bucket slipped right into place. Easy to install.
As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.
Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)
With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.
Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!
Freezer coils covered in ice - Refridgerator and freezer quit cooling
Removed screws on back cover plate in Freezer, disconnected fan assembly, removed fan assembly, removed propeller from fan assembly, and transferred it to new motor, installed new assembly, reconnected electrical connections, screwed on back cover plate - Viola!
Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble the refrigerator, it was fully operational. Very easy to do and only required a few tools.
Temperature not low enough, frost build up on coils
Defrost fan was not coming on, extreme frost build up on coils in freezer compartment. For troubleshooting purposes, bypassed thermostat to see if fan would work. Just cut wires and wire nut them together. Fan worked OK so figured the thermostat was bad. Considered the defrost timer, but it was working OK as I could see it advancing, and there was voltage to the thermostat. (120vac) Anyway, once I received the new part, it simply just plugs in to the existing connectors. The test connector has to be pushed through the back access hole, which is sealed by a flexible putty, make sure to get it sealed good, its re-usable. Only had to remove two pannels, the one on back and the lower one in the freezer compartment, all you need is a 1/4" socket for both. Repair was easy, but it will take some time for the temp to come down. Very important- make sure you clip the thermostat to the coil or you will not cool properly, this is so that the temperature transfer can take place, the cold air is not enough to do it.
My icemaker started leaking water into the catch basin and turning my ice into one big ice burg.
Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off. Well don't put this one off because this is just how easy it went. I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped. After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice. Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part. One quick order and in three days it was right there by my door when I got home. Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs. The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!
First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!
Service and shipping were fantastic! I would definitely use Partselect again!
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.
Ice maker tray would overfill tray and create large clumps of ice.
Repair Refrigerator Kick Plate Grill: No tools were required. I removed old grill with hands. I attached two clips to new grill, and re-installed the new grill. (less than 5 minutes very easy)
Repair Crushed Ice Bucket: You will need sockets or nut driver. Remove the Ice crusher dispenser and metal rod from the existing unit. You will then re-install with the new Ice Bucket. There were two scews that held the front cover. You will need to remove four screws to remove the ice crusher mechanism and re-install with new bucket. (10 minutes to replace)
Repair Ice Maker Assembly: I removed the plastic cap on the top left edged of the ice maker. You will need to use your existing cap with the replacement unit. I then loosened the top two screws on the ice maker assembly. You do not need to remove the top two screws. There is one screw on the bottom that will need to be removed. This will allow you to get to the wiring harness. I pulled out the white tube that fills the ice maker with water. I then used a small bucket to pour existing water out of the ice maker. I used a small screw driver to depess the clip on the wiring harness. You can not pull out the wiring harnes unless the plastic clip is depressed. The new ice maker assembly did not have the same type of water line attachment. It looks like it is made for different assemblys. For my water tube, I noticed a notched area on the new unit that could be cut out to work like my existing unit did for the water line. I used a box knife to cut out the notched area. On the new water tray, there was a hole in the side that my existing unit did not have. It does not affect the installation of the water tube. I installed the new ice maker assembly by attaching the wiring harness. Installed the bottom screw using my original bracket instead of the new bracket that came with the new unit. Tightened the top screws and bottom screw. Attached the water tube to the ice maker assembly. Attached plastic cap between the refrigerator wall and left side of the ice maker assembly. (15 minutes)
removed the back panel inside the freezer (several small screws) with a nutdriver. used a hair dryer to melt the built up ice. replaced the thermostat and replaced the panel. very simple repair.
Unplugged the refrigerator. Removed the screws from the access panel. Replaced the bad motor with the new motor. Works great . Probably saved myself $125.00 in a repair service call.
The web site and customer service from Partselect.com was outstanding. I had the part in two days. Their tracking system is wonderful. First class company.......It's plain to see they put the customer first.
1. Take out the refrigerator door. 2. Take out 20 nuts. 3. Take out old gascket. 4. Put in the new gascket. 5. Put back the nuts. 6. PUt back the door.