Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Machine would not power up
This is a long, sad story, but I'll cut to the chase. I was told by few appliance repair guys that my problem was most likely due to the motor being bad. I had checked the thermal fuse, the door switch, and the power switch, and all were good so that made sense. I then saw a video which made it seem fairly straight forward to remove the old motor and replace it. So I ordered the motor from Part Select. Turns out it's impossible to remove the motor without also removing (and replacing) the blower. The video never mentions that. Also FYI, I found out that my dryer switch WAS broken, and nothing was wrong with the motor, so I spent $250 on a repair that should have cost %40. Oh well ...
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
F 3 error
I did the repair following your instructions and it went very well. Now the temperature is working good , but the oven is heating up very slow. So now what should I do to fix the oven?
un plug, gas shut off, nut driver back cover, remove lint screen, slide top forward and lift. disconnect close sensor- front. remove front. remove drive belt and tub. get wife dressed in cookie monster footie pj's to hold motor with wrench while reverse threading fan. remove motor- order from this site, got motor next day. reassemble less than 30 minutes. Impress wife and get lovin!
Dryer would only run for a few mins and then not restart. Also there was a grinding noise.
I replaced the entire motor in the dryer and the belt while I had it open and it is working great! I just watched the short video on the site to learn the tricks and did it myself.
Pulled racks and covers out of oven. Moved stove away from wall. removed bolts holding igniter. Disconnected wiring harness. Reverse process to install new part.
loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
Dryer buzzed when trying to start
First off, I ordered the part around 1 pm, paid regular shipping, and it was here the very next day! As for the repair, maybe the easiest fix I have done. Make sure the dryer is unplugged, pop the top up and remove the front of the dryer. Take out the pulley (careful it can snap ya) then remove the drum. The snap rings around the motor can be tricky, so be sure to watch the video sent to you from PartSelect. With a couple of wrenches, loosen the motor from the blower and remove. Put new one in and put back together. Piece of cake. Took me about 20-25 mins. This is the best place I've ordered from and will continue to get my supplies here. Good Luck!
took top off,took back off,took lower panel off,removed old motor without taking drum out,got the part # off old motor,looked it up on line then i found the video on how to do the repair...lol. The repair went well and the instructions that came with the new motor were very good as my motor had the old style switch and needed to be rewired. I did go one step further as long as i had it that far apart,I took the duct work apart on the back of the dryer for the vent and I was very glad I did,it had 25 years of lint and all sorts of other thing in it.I cleaned and lubed all other moving parts and reassembled,works and sounds like new !
I watched the informative video you sent via e-mail with order conformation. Installation was flawless. Thanks and will be using your site again for any other small appliance repairs that may need my attention.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
The surface burner socket that the burner plugs into melted.
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.
one burner that would not heat and others that would not out out much heat
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove the screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Burner keep coming on and going off had a short in burner plug-in block.
Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!
