RT12VKYHN02 Roper Refrigerator - Instructions

Whirlpool refridgerator, parts were not exactly the same,but did fit. The electrical hook plug was perfect. Old ice maker had wear marks in channels. Installed new ice maker. Pump still didn't operate after letting ice box get down to normal temp. Replaced pump. Had to use hose permanentely attached to new pump. Removed old hose and clamped new hose at top and outside refrigerator with existing clamp. Let the freezer get back down to normal temp. Ice maker operated perfectly.

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

The icemaker came with very easy to understand instructions the installation took less than 45 min. that included installing the selinoid valve and waterline I had a nearby waterpipe, the acual icemaker took about 5 min. to install it in the freezer.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.

Per instructions

I completed the ice maker installation but the bracket the automatic water valve was attached to in no way would fit my Whirlpool fridge. The one showed in instructions sent with the ice maker was different than the one Partselect sent me. I had to grind both sides of the bracket off and just hot glued it to the spot where it was supposed to go. I can see how this could be a real issue for some.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

took old one out with a screw driver,replaced it with the new one. works great!. din't have to put part on at back bottom.I will say this.you guys sure got the part here fast! thanks..

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Installation went smooth - only three hex-head screws (one below unit and two above. After removing 3 screws, unit comes loose in your hand but is still connected by a plug leading 4 wires to a connector visible through a slot in back panel of freezer compartment. New unit goes in easily (making sure spout from pump that protrudes from back wall fits through opening on icemaker) but there's not a generous amout of wiring harness and the 'female' of the electrical connection is recessed and loose inside a cutout in the rear panel so you can't get a good grip on it nor can you feel if it plugs securely. I plugged new unit into connector and then secured it with the 3 screws, waited the 12 hours per instructions, but no ice. Removed unit and guessed that the plug had not seated fully (not plugged in.) I took a short piece of a wooden paint stirrer and put it on back edge of plug and tapped it into place so it seated fully. Immediately, the pump cycled and water came from the filler spout, so I surmised that it was now properly plugged in - it began making ice in a couple of hours and has operated perfectly ever since. Lesson learned is to make sure you get the electrical connector fully in place - mine did not 'snap' or 'click' into place and I wrongly assumed it was plugged in correctly.

After ordering the ice-maker, but before it had arrived, I installed a valve in the pex water line in the room right below the fridge. I had to rent a pex clamp kit from Home Depot. It cost $8 for 4 hours and came with the crimpers and band cutters. I then ran a poly line to an in-line filter which I mounted to an exposed stud and fished the line up the wall and out a small hole I drilled behind the fridge. When the ice-maker came, it took less than 30 minutes to install and start my first batch of ice. With the in-line filter, the ice forms with practically no sediment flakes. Part Select was the only place I could find a replacement ice-maker. In addition to the parts in the ice-maker kit, I had to buy 12 feet of poly water line, a ball-valve, the in-line filter and a compression fitting. A total of $20 at my plumbing contractor store.