RT12DKYAW00 Roper Refrigerator - Instructions

I was pleased with the new ice maker and how soon I received it. I was disappointed because there were NO installation instructions that came with it. There were only service instructions that came with it. I contacted partselect and was told that they get the part from whirlpool and they are responsible for everything and was given a phone number to call. I called Whirlpool and was informed that they don't provide installation instructions, I said that on the web page is boldly displayed an installation instruction sheet. Whirlpool said that they expect that the installation person knows what they are doing. I let it go and was very careful taking the old one out and installing the new ice maker and the new pump.

Since the defrost timer turns the cooling functions on and off for each defrost cycle if seemed the most likely problem. That was confirmed by manually advancing the timer with a screw driver and the cooling functions would resume and run until the next defrost cycle (every 8 hours or so). The repair itself was to swap out the timer which took five minutes with a #2 phillips screw driver and a 1/4" nut driver. Once the timer was removed from the cover plate there's a simple plug-in connector to remove from the old and plug into the new timer. Two machine screws hold the timer in place behind the cover plate. Be sure switch the power off on the compressor cabinet before removing the cover plate.

Replaced original ice-maker with the ice-maker from the kit. Operational check was good.

The repair was super easy and the part worked like a charm. I love my new ice maker! I had to take out the top freezer shelf just so I could fit my head in the freezer to find one screw, but otherwise all went fine. Ice maker is held on with two top screws and one bottom screw. Loosen the two top screws, remove the bottom screw and lift out the ice maker. It plugs into wires on the inside, back of the freezer so this has to be unplugged. Plug in the wires for the new one, slide it down onto the two top, loose screws, tighten those and screw in the bottom one, replace freezer shelves and you are ready for ice...with no huge iceberg fouling up the ice in your ice cube tray. Simple! The wiring thing worried me when others described it, but it's no harder than plugging in a lamp, really. If I can do it, anybody who can stand on a shorty ladder can do it.

The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha comes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.

Went to various websites looking for guidance. Finally went to PartSelect since I had previously purchased dryer parts. I entered the model info, etc. from my refrigerator and ordered the ice maker installation kit. The install was fairly easy and everything worked perfectly. I am very satisfied I could do the work myself versus calling a repair technician.

removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. Replace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.

Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.

After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

The most difficult problem was determining what part I needed.Once I was able to find the parts description, selecting the part was easy. Ordering the part was a simple matter of following the instructions. Imagine my surprise when I received the parts on the very next day!! The installation of the new parts was very easy. Thank you for keeping me from buying a new refrigerator.