Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the oven handle broke during delivery
I remove the damage handle from the oven door,Then i install the new door handle with no problem.The tools i used was a hand nut driver and a phillip #3driver.
I ordered a new display from the internet. I removed the panel where the display is housed, unscrewed the entire display assembly and unplugged all wires connecting it. (I made a drawing and noted colors of wires) I removed adhesive face of display and replaced it on the new display. I then screwed in the display and reconnected the wires as per my notes. I reassembled the panel and applied power and it worked like new.
It was very easy I removed two screws unpluged the sensor and wire spliced it together and also replaced the modual on the top of the stove and it was that easy.
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.
the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino
While I was waiting on another part to arrive, I decided it would be a good time to do a thorough cleaning. When I lifted the top of the range, I lifted it to far and cracked both front burner tubes. The top of the range should not be lifted more than 4 inches without removing the 3 screws that hold each burner in place. When the new lines came in, I removed both front burners, knobs, and then removed the front plate behind the knobs using a Phillips screwdriver. The screws are located on the bottom of the plate. Using my adjustable wrench I replaced the lines. Then I CAREFULLY bent the gas tubes and remounted the burners. Over all an easy install. Just be careful, the gas tubes are aluminum and will break very easy. This is the second time I used PartSelect, and I am very satisfied.
Wife dropped a cast iron pan, it bounced and broke the front glass
On each side of the door at the top you will find an allen screw, remove those to remove the handle assembly. On the inside of the door, you will find two more silver allen screws, these release the glass frame. On the flimsy part that seperates from the main door frame, there are two small brackets that hold the glass panel. Remove those using a #2 philips head screwdriver, then using a flat head screwdriver, carefully pry out all the ramaining glass shards. The glass frame will be very wobbly, this is a good time to have a friend around. place the new glass panel in the bottom slot first, then just hold it up, with a helper on one side, and reinstall the top brackets. These fit tightly on the glass, so expect to have to push a bit. now reinstall the screws, fold both parts together, use the silver screws to reconnect the glass panel assembly to the door frame, and reinstall the handle. Now you have a nice new door front!
First I removed the back panel and then removed the four screws that hold the display board in place.I then disconnected the wires. I installed the new board and connected the wires. I put the back panel on. I installed a serge protector and pluged in the range. Job completed and it worked.
First I tested oven sensor which checked o k. I then made a diagram of the electrical wireing to the oven control. I disconnected wireing and removed the control then with sharp knife I removed touch control pad. I placed th touch pad on the new panel and installed panel and connected wiring. Pluged into wall rec and test oven which checked o k .