Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Oven would not turn off due to inoperative thermostat
1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.
ordered parts, 2 double burners, 3 days later they arrived.opened box. lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID. units purchased were exact replacements. supplied spacer nuts not needed. easy fix looks new again, thanks.
Lifted the top and dropped in the new burners. Realized they always should have had the leveling washers provided so I took the burners off, dropped on the leveling washers and dropped the burners back on. This all took about 2 minutes. Really made the range top look a lot nicer.
I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!
First just unscrew each natural gas jet and install the propane jets. if they are hard to come off just turn your wrench back and forth first until the jet turns with your fingers. Then open the oven and take out the racks. In the bottom back of the inside of the oven there is a screw on each side. Unscrew both screws lift the bototom plate of the oven and slide it back about 1/2 inch then lift out of the oven. Move the 1 screw covering the heat shield from the oven jet. Then light the top burners and turn them off just to get the gas flowing. Also light the pilot in the oven, then light the oven. To convert the oven from natural gas to propane all you have to do is adjust the jet while the oven is lit. turn the oven jet ubtil there is a blue flame with little or no yellow tips on the flames.
Remove the cover over the spark module. Remove the two screws holding the module. Unplug the wires from the old module and plug them into the new module. Install the new module with the two screws. Replace the cover.
I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered new ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.
The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!