Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
leaking around the valve
removed card board protection.4 screws. Unpluged refrigerator unscrewed the screw holding the valve but not all the way. disconnected the electric connection. removed the water connection after disconnecting the main water valve. replaced valve by reconnecting everything. Turned on water to check for leaks. Easy fix and recieved the part sooner then expected. Will highly recomend your fast service and correct part replacement. web site was easy to use. THANK YOU
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!
Diagnosis: Defrost timer tested fine for continuity. Removed relay/capacitor unit from compressor (carefully). Tested compressor connections for continuity (OK). I tested the connection paths from timer to compressor and they were fine. At this point, I figured it could only be two things: [1]bad compressor or [2] bad relay/capacitor. I put the odds on the relay and bet the $70 on the part. Before installation, I marked the timer position with a sharpie. It's located on the ceiling of the refrigerator compartment. After the part installation, the compressor kicked in, purring quietly. Condenser coils warm, Evaporator coils cold. After a few hours I had ice in the freezer. I checked the timer markings with a compact mirror. It had advanced over a half turn, assuring that the timer motor functions. . Next, I went to the grocery store.
One pair of freezer door stop basket brackets broken
First I used needle-nose pliers to remove broken hooks from the door. (One of the broken hooks slipped down inside the door and could not be retrieved. It will not create a problem is you cannot remove broken hooks.) I examined the hooks against the bracket to check the hook orientation (up or down ... they faced down). Next I searched online for the parts and discovered my door decal model number needed one or more letters, and I could not find the serial number. I only knew it was a 10 year old Maytag model RSW2400E.
All online websites (no matter what model version I used) said the basket door stop brackets were obsolete and no longer available. I finally found Partselect.com and used their easy search system to find pictures and descriptions of the parts. But I could only find parts with upward facing hooks. I was concerned but decided to take a chance and ordered them because they looked like they might fit. I had nothing to lose since the original parts are no longer available. When the new parts arrived, they looked just like the broken ones except for the hook orientation, and the packaging listed them correctly as "STOP. BASKET (LT) part #61004465" and "STOP.BASKET (RT) part #61004466". I held them up to the door (while still in the packaging) and they looked good.
INSTALLATION: First, I inserted the left-hand bracket hooks into the door panel holes (you can start with either the left or right side) and gave it a little push and it snapped into place. The hooks and the little stop node fit perfectly and flush. YES!
Second, I took the basket, and making sure it was facing the correct direction for tilting in and out, I inserted the basket pivot post into the pivot hole on the stop bracket (making sure that I had the basket frame to the inside of the stop so that the basket would catch and be stopped when tilted out).
Third, I got the right-hand bracket and inserted it onto the other basket pivot post BEFORE I installed the right-hand bracket into the door.
Lastly, while holding the basket and the bracket together, I inserted the bracket into the door and pushed it into place.
I checked the basket operation. It tilted perfectly. There were no clearence issues. WOOHOO! Job done in less than 5 minutes, THANK YOU PARTSELECT.COM
I would only ask Partselect to adjust the online description to "Door Basket Stop - Left Hand and Right Hand" (Door Shelf Retainer Bracket is not correct.)
(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!
I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98. So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one. But Parts Select is a great place to order from. Thank you.
Sides and door frames of the refrigerator warm to the touch.
Confirmed the condenser fan was the problem when I noted it was not running when the compressor was on. Removed 3 mounting screws, unpluggede the fan. Removed and replaced the mounted flange(3 screws) and remounted. Plugged in fan and it started running.
Thanks for the diagrams and quick delivery. This is the second repair on appliances I have made with your parts and probably saved $300-400 in service calls.
Broken left side slide rail for the meat/cheese bin
Removing the broken rail was very difficult. There is a small notch that actually holds it in place. To remove the old rail, there was a hole in the metal bracket next to where the notch was. You had to apply pressure through the hole to the rail to slightly bend it to get it to release the notch to slide the old rail out. After the old rail was removed, the new rail with rack wheel installed, slid in and snapped into place very easily.
I don't know anything about repairing a refrigerator - I'm a computer tech. I noticed that the outside of the fridge was warm to the touch and the inside was not getting as cold as it should. I took the lower back panel behind the fridge off and noticed that the fan was not spinning. The local parts dealers did not have the condenser fan motor that was needed but they did say that they do go bad. I decided to order one from PartSelect.com and do it myself. Using a 1/4 inch nut driver and a flat head screw driver to pry the old motor out of the casing, I got the job done in about an hour or so. It's a relativly easy job. Besides the ouside panel screws, there's 3 screws on the inside near the fan blades you have to reach in to get. Pop out the whole assembly, unscrew the nut that holds the blades on and pry out the old motor and replace.. Try it yourself and save a couple hundred bucks!
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed
Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.