I didn’t do the repair because the new motor had a female pigtail connector while the original motor has male connection. It came with wire clamps but didn’t want to cut wires to make repair. The pictures online show a male connection. Put the old motor back in and now it works fine.
defrost heater not working; defrost timer not rotating so coils ice up
Checked for continuity in heater, defrost thermostat and defrost timer. Heater good; not sure about thermostat or timer. Replaced thermostat - no change. Replaced timer - rotating and heater working.
sometimes it would go into defrost and would not go back to cooling.
I called the repairman who diagnosed the problem as a thermostat then had to order a thermostat took about 2 weeks to get back and install (cost little over $100). did good for about two weeks and same problem reoccured. I decided it was defrost timer and ordered from this site for $19.95 including shipping. I got on ( you tube ) and got instructions(recommend you tube) for DIY install about 15 to 20 minutes. Has been running great for about 3 weeks. ( YOU TUBE IS GREAT FOR A DIY REPAIR ON ABOUT ANYTHING)
Seal was old and cracking allowing condesate to rust the door
I should have read everyone else's experiences before attempting. I did view a youtube video and thought I had it set. However, if I had it to do over, the door would have been removed. The door shelf (inner door) taken off and cleaned before attempting to put the gasket on. I did it while the door was still attached and probably lost a good 45mns along with my fingers cramping, knee's flat spotting, and lower back catching fire. TAKE THE DOOR OFF if at all possible, you wont regret it.
Was really basic, simply slide off the old caps, slide on the new ones, put the shelf back where it goes, push down lightly so as to not snap the new caps, and viola, complete. No more than 2 minutes worth of work. Great part at a great price, shipping was more than the part itself so I bought 2 of each. Only problem I ran into was that I ordered the top shelf caps instead of the bottom the first time, so I had to reorder.
Freezer frosted up, refrigerator compartment heated up
I removed the housing at the top of the refrigerator compartment that contained the reefer light and temperature adjustment knob. This required a small nut-driver. Inside, I found the old defrost control, unplugged it, unscrewed it with a Phillips screwdriver, and replaced it with the replacement part. Then I replaced the housing to its original position.
Removed the housing with the light, 4 hexhead screws. This exposed the defrost timer, removed 2 hexhead screws, electrical connector and reassembled the unit.
Door shelf retainer bar end caps broke off at insertion point.
Removed plastic male parts. Inserted new end caps onto old retainer bar. Inserted all into door. A snap, but I didn't need to order the retainer bar after all - the old one was the perfect fit and the one I ordered was way too long. I returned the new retainer bar, and the shipping was more expensive than the part.
First I removed the plastic grill (pulled out, no screws) from bottom of refrigerator, then I removed electrical plug & two screws from old timer (timer located on the front inside left lower side of refrigerator). Installed in reverse order.
There was no work to do. I just slipped the new drawer in. I'm writing because PartSelect was amazing. A rep on the phone helped me identify the part I needed--which was a substitute b/c the actual part isn't made anymore. The next day, the part arrived. I was blown away and want to acknowledge the great service.
I removed the plastic shroud on the ceiling of the refigerator, unscrewed and unplugged the old defrost timer, and replaced it with the new one. I reinstalled the shroud with the new timer installed.
removed all items from frig.. removed shelves, loosened one screw on each slide bracket and moved them down and out of the way of the rear panel....removed 6 screws in rear panel...removed all ice on coils with a heat gun...located defrost stat, replaced...crimped wires...re-installed rear panel and shelves! On left side of frig. in front bottom..located defrost timer..removed trim piece, loosened 2 screws....removed and replaced defrost timer...plugged in the frig. and it started!!!!
The refrigerator in my new apartment was missing the brackets that hold the bars so that things don't fall off of the door shelves. It was missing several off of the refrigerator door and one off of the freezer door.
I just had to make certain I had the correct end-cap for the correct side. I placed the two little curved pieces into the slots and applied some downward pressure (gently) onto the end-cap till I heard it "snap" into place. You could then see that it was held in place securely. I did first one side, then fed the bar into it, then placed the other side onto the the bar; inserted the end-cap and secured it in place.
HINT: I myself mistakingly ordered the same exact end-cap for both the freezer and the fridge doors. I was unaware (I failed to check), that the end-caps for the freezer are not the same end-caps as the ones for the fridge door. My refrigerator uses three different end-cap sizes; one size for the actual fridge door and two additional different sizes for the freezer door. Not wanting to exchange it, I used the one I ordered anyway. It still works, but makes the bar protrude into the freezer more than it would have, had I ordered the correct size.
SPECIAL NOTE: This company got the correctly ordered products to me within a couple of days. I would definitely order from them again without hesitation. I am very happy with the product and service. Smooth.