Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water inlet valve was clog. water was very slow to fill the machine.
I unplug the power plug, turned off water supply and unsrewed the water lines connected to the clogged valve.I unsrewed six screws on the front of the washing machine and took the front panals off. lifted the the washing top and replace the hose and intake valve, which was shipped to me. put the top down and put the two front panals. reconnected the water supply to the new valve and turned the water back on. connected the electric plug.works as good as new.
Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!
Hose was in contact with bracket for tub causing the hose to wear thru.
Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.
Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.
No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.
First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!
It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks
Taking the hub out was a promblem because, with a puller it did not come out. It broke off while pulling out we had to drill it out had to brake off.You need a 1 1/2 inch deep socket with a impact wrench. It was a hassel but got done. I replaced the whole seal kit and it is still leaking it leaks from the bottom of the tub. It leaks worse when it has a heavy load I dont know what to do.Need help.
1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump
Unplugged washer from power source. Dissconnect the water supply. Take off lower panel. Undo big spring. Remove 4 bolts that hold the motor. Unplug the motor. remove motor and belt. While on the bench I regreased the Idler pulley. then reverse the procedure to reassemble
simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.
I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.
pulley was worn out and would not turn belt was also worn outand had chunks out of it
Laid washer on its side and had to remove the motor,replaced the pulley and belt replaced the motor and put all parts back together washer spins and runs like it did when it was new.we did not need the screw or nut but did not know when ordering parts
Remove the front of the washer. Remove the pump and motor assembly using the 1/2 inch socket. Remove the pump from the motor and hoses from the pump. Replace the bad idler pulley and place new belt on pulley. Reassemble the pump to the motor and install the assembly back into the washing machine. Reasemble the hoses and put belt on driven pulley for the drum. Reinstall the front cover.
had to completely disasemble whole washer drum and mechanical components to remove upper bearing on transmission,the drum hub was corroded on the shaft. I had to use a gear puller and a propane torch to get the hub off upper shaft of the transmission. then press the bearings in the respective sheet metal supports. reassembly was alot easier than taking it apart. Not a job for an average homeowner. It would not have been repaired without the wheel puller. all the seals were reusable A week and a half of use later no leaks and works great
Removed and replaced mixing valve. Shut off hot & cold water supply to machine. Pull machine electric plug. Access back of machine. Remove water supply to machine. (Pliers) Be sure to keep some paper towels handy to pick up residual water. Remove screw that holds mixing valve mounting plate to machine. Pull plate away from machine. Undo hot and cold elect. connectors to valve. Remove water supply to valve. (Black hose-screwdriver.) Remove screw holding valve to mount plate. (Nut driver.) Install new valve onto mount plate. Reverse process used to remove valve. Test by turning on machine.