Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door had a poping sound when opening and closing
Removed the trim screw on top of the door then removed the two hinge bracket bolts. lifted the door off placed on the table. Remove the two screws on holding the bearing bracket on the bottom of the door. removed the bearing and replace with the new one. Reinstalled in reverse order.
Most of the time was spent removing frozen food and removing the plastic clip holding one of the shelves in place. Removal of bottom panel took less than a minute. Thermostat easy to find, clipped wires a the unit and removed unit. Used included wire jackets, but not white shrink wrap. This did NOT fix the problem. This was the attempt at a 'cheap' fix. My refrigerator required the 'control box' to be replaced.
Once I recieved the new filter, I enthusiastically opened the box, removed the filter from it's packaging and set it aside for quick access. I opened the refrigerator door, pushed the release button on the old filter and pulled it out. I then tossed the old filter in the trash. Once that was done, I removed the 2 rubber caps covering the inlet and outlets on the new filter. Then, with ace precision, I guided the new filter back into the slot until it clicked. I ran the water for 3 minutes as the instructions suggested, then, had a glass of water. Mission accomplished and it went off without a single hitch!
Removed the cover inside the freezer. Found out that the motor/fan was not working. Ordered through PartSelect. Got the parts in 3 days. Installed it for less than 30 minutes. Very easy. It saved me hundreds of dollars. We considered buying a new fridge but not anymore. , it only cost me $70 including shipment charges. (Make sure you unplug the appliance first before opening the cover. Remember safety first.)
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
The 4 lines attached to water valve have compression fittings.New valve has pex fittings.I cut each line just behind the ferrel and inserted each line into the proper fitting and reattached the 3 electrical plugs.Turned water back on.I immediately got water from thr door without dripping.For whatever reason it was not making ice for the first 3 days,I pulled the plug on the icemaker solenoid and reattached.It is working now.
Freezer was cold but the fridge was warm. Back panel of fridge was building up frost
First of all Don't panic! you can do it and you can save a lot of $$$ if you do it yourself. A friend advice me to look it up online resources and came accross part select on YouTube .
The process: Defrost the fridge. Take down the panels on the fridge to have room to unscrew the back panels. Once you've taken the back panel out. You will see the thermostat right away. Replace it and voila you're done.
It was fairly easy. Only had to remove the back cardboard. Remove 3 screws and the power plug. Replacing the screws took a little time the motor mount didn't seem to be tapped exactly for the screws supplied and it was in a tight area. Its working great now.
I pulled out the old support stud with a pair of pliers, pushed the new stud in, and gave it a few taps with the hammer to secure it in the fridge wall. For the door bin I just slid the new bin in place.
The door had a loud popping noise everytime you opened it.
The biggest part of the repair was getting everything out of the shelves in the door. I had to remove one phillips head screw from the plastic hinge cover on the top of the appliance. As per the owners manual I traced around the hinge with a pencil so I would be able to align the door to the same postion. Removed two screws with a nut driver and removed the top hinge. The magnetic strip held the door in place until I grabbed it and pulled it open then lifted it up off of the bottom hinge. I layed the door on the island counter and pried the bearing hinge out of the door stop and replaced it with the new one. I probably could have stopped there but figured the plate might have been worn so I remove one phillips head screw from the bottom hinge, lifted the plate off, and replaced it with the new one. I assembled everything in reverse order and voila, no more popping noises.
Hinge bearing broke causing door to rub when opened
I removed the screw in the plastic cover on the top of the fridge that covered the fridge side hinge first. Then, I removed the two nuts with a nut driver that hold the hinge in place. After removing the two nuts and the hinge, I lifted the door up and out of the bottom hinge and placed it on a flat surface. I used a pair of pliers next to pull out the broken hinge bearing from the bottom of the door itself. After removing the old bearing I inserted the new bearing in the door. Next, I put the door back on making sure the hinge went into the hinge bearing and put the door in the closed position. After that was all done and the door was set properly, I put the top hinge back on with the two screws and put the plastic cover back in place. Took 20min to complete. A second set of hands would have been helpful with putting the door back on, but it can be done by yourself.