Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave fan would come on when door open. Timer and unit would not switch on.
I looked up my problem on the internet and found a very helpful video. Microwave on video was different brand but the internals and methods were very much the same. The video made it simple and easy to fix. Found the replacement switch on the LG parts site and ordered. Two different switch types. One with red switch, the other green. Part was $7.28. Saved a bundle in service costs. Here is the repair video.
Take off cover then the bottom. Transformer is on the bottom plate and wires won't let it come all the way off, too many wires to pull off so will have to position the bottom plate so you can get to the motor. Remove 1 screw on motor and remove motor. Install new motor connect wires replace bottom plate, replace cover. All done (hope & pray it works ok) mine worked perfect. Hope this helps.
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Unplug.Take off the external cowling from the back of the unit by removing the torx security screws. Tip: instead use a thin screwdriver blade to unscrew the torx screws, or knock out the center pins of these screws. Remove the bottom panel. The replacement motor is attached with one phillips screw, re-attach wires to motor - polarity doesn't matter. Re-assemble and you're finished.
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Overall repair quite simple. Removed screws from the sides and rear of the microwave, then removed cover. Next, removed only the screws to separate the bottom cover. Removed the one screw in the AC Synchronous motor to remove the motor (had to use small screwdriver through a vent slot in the bottom to remove the screw). Unplugged and removed motor. Installation is the reverse of removal. Note: on the back of my appliance were 4 torx screws with a tamperproof pin in the center. I used the rotary tool to grind out the pins so I could use a regular torx bit instead of ordering specialty bits.
Intermittent loss of power in open and closing door.
Make sure 110v at the transformer. Activate switch controlled by the push button to open and close door. Push in the small metal arm on the switch with none metallic probe. If power is restored to microwave the switch is faulty and need replacement. One switch is not available, the whole 3 switch assemble has to be purchased.
synchronized motor died a terrible death and stopped turning.
Eight screws off the bottom exposed the cover plate. Easily found the motor location the looked up the item number and verified data and ordered the part. Replaced the motor, tightened the screws and flipped it upright. Plugged it in and the lights came on. Set a time pushed start and smiled! The eagle had landed!!!!
Carousel would not turn. Small plastic drive shaft broken.
Pried cover off bottom-center of microwave. It seems to be either glued or lightly tack welded. Removed 2 small Phillips screws to remove motor. Disconnected electric feed by hand. Don't let go of electric wire or small screws. They will be hard to retrieve from behind the rest of the metal base. Reverse process to install new motor. Didn't try to put small cover back on.
Microwave turntable did not turn, or dragged/stuck
I had previously replaced the turntable motor, which helped for a small while. When the problem occurred again I examined the turntable assembly (small wheels which support the glass tray as it turns). The wheels were all flat on two sides. It may have been a defect from the beginning or a result of our placing food off-center because this model has a terrible cold spot in the middle of the microwave pattern................ The repair was as simple as taking out the glass tray, pulling the assembly (plastic arms with wheels on the end) off, dropping the new assembly on, and replacing the glass tray.............. This is surely worth a first look before replacing the turntable motor.
the turntable on the microwave quit turning even though the microwave would heat up
I removed the outer cover of the microwave and removed the bottom palte to access the small motor. i unplugged the old motor from teh wiring connector, removed (1) screw and motor came out. I reversed the proceedure with the new motor and it was finished.It was a piece of cake.