Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Refrigerator door didn't close on its own
First I completely emptied out all the inside of the refrigerator door to lighten the weight of the door. Then I removed the 3 screws on top of the fridge which held the door in place. It was pretty easy to lift up the door and remove it from the bottom hinge. I removed and replaced the door closure and re-assembled the door.
Unfortunately that didn't fix the issue. The door still doesn't close on it's own. The door doesn't get lifted up at all when I open it so I assume that the counterpart to the door closure within the door itself is broken.
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
We thought the water valve was bad, but it wasn't The problem was the ice maker. We sent the valve back for a refund, and in addition there was no valve available that replaced the old one.
Took the ice maker out with three screws hving turned water off and unplugging fridge. Put a new one back in with the three screws. plugged fridge back in and turned water on. All done and everthing worked fine.
Water Intake valve for icemaker in Amana refrigerator We found that the icemaker was not getting water due to a faulty intake valve. The original valve had a plastic coupling on the vinyl tube leaving the valve. The replacement valve had a quick connect coupling. Replacing the valve with the new part gave a significant leak. After discussion and viewing YouTube directions multiple times, the part was returned; and a new part was sent. It also leaked. After searching, a video was found that dealt with the no-fail quick connect. The problem was not in the quick connect but in the tube from our refrigerator which had a spring inside the last five inches of the tube. This aided the prevention of a leak when the original plastic coupling had been installed. SOLUTION: Removing the part of the tube with the spring using a clean cut allowed the quick connect to work preventing the leak. This needs to be mentioned in the how-to videos to save others having a problem. Also, these instructions with the part would be helpful.
The longer than usual repair times shown above were the result of the spring insert in the plastic water tube of the refrigerator. Nowhere in the how-to instructions were references made of either an insert in the tube or quick connect procedures.
We were well pleased with the support rendered by the PartSelect staff.
Exposed evaporator and fan.Turned refer back on. Evaporator started to get cold but fan did not run. Removed fan and applied 115 volts. Fan did not run. Installed new fan kit. Old refer works as good as new. Vary easy job. I almost bought a new refer. Glad I didn't. Probably saved myself $500+ Shopped several sites on internet. Other sites wanted about the same price for motor only and 15-20 bucks more for the fan. Vary pleased that I found this company to buy this part. Received fan kit in just a few days.
Used online resources to deteremine that it was either the icemaker not telling the valve to open or the valve no opening so ordered both and started with the valve (cheaper part). Turn off the water, removed the mounting screws, disconnected the plug, removed the water line (used the wet vac to suck up water while it leaked out). and disconnected the inlet line. Reconnected everything in reverse order but left unmounted until sure it worked, turned water on and waited.
Ice maker started pruducing smaller and smaller cubes until finially it was not producing any cubes.
Really easy. Turned the water off, unplugged the fridge and took off a few bolts and swapped the valve out for new. It was basically plug and play. The ice maker started working its next cycle.
Burned out socket, right side of refrigerator compartment.
I was changing a defective bulb and somehow the hot lead for the socket got grounded, and arched. This made the socket defective. I simply took out the defective socket and replaced it with the new one I ordered. Working fine now. PCH
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.