Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
LIGHT SWITCH ON LATCH-DOOR BROKEN
REMOVED PANEL COVER [ 4 SCREWS] UNSCREWED 2 SCREWS ON LATCH DOOR ON THIS MODEL THE PART WAS IN TOO TIGHT OF QUARTERS SO I HAD TO LOOSEN A TOP PANEL SO I COULD RAISE PART HIGH ENOUGH TO RELEASE IT FROM A CATCH AT THE BACK OF THE PART. PUSH PART BACK, RAISE AND PULL FORWARDS. REMOVED 4 WIRES ONE AT A TIME AND ATTACHING TO NEW PART. REPLACED PART, TIGHTEN TOP PANEL AND REPLACED PANEL COVER.
1. Turn off the breaker. 2. Remove all of the oven racks. 3. Remove the oven door as per users manual. 4. Remove two 1/4" screws on the plate holding the broil element to the back of the oven. 5.. Remove two 1/4" screws in the front of the element holding reflective plate and element toward the front of the oven. 6. Carefully pull the element out enough to remove the wire spade contacts with from the rear of the element with long nosed pliers being careful not to let the wires go behind the rear oven cavity. 7. Element and top reflective plate assembly can now be removed from the oven. 8. The old element is removed from the reflective plate by removing four 1/4" screws. 9. Install the new element on the plate and reverse the procedure to reinstall the completed assembly into the oven. 10 Reinstall the door and racks, turn on the power and test.
Sensor went out after fire in oven fault code 1b11
I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.
We bought a really nice microwave for about 1/3rd of the MSRP, but it was an open box item and when we got it home we found that it was missing a bracket on the inside of the microwave. We were able to replace the bracket easily thanks to partselect.com.
Should be about 1 5/8 inch with 3/8 inch prongs. Sent bulb won’t fit. JennAire book showed Part 74004458-halogen bulb part PS 11765655 was substituted. I paid additional shipping so my son could install when here. My husband and I are 79 and unable to bend into the oven. I need the correct part where do I return the unopened $29.95 bulb for credit on my card and receive the correct one????? Carolyn Sanders 817-319-6581 Order 21938961
I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring. After that it was a snap.
I spoke to Daily via the phone and I ordered a new steamer since my original steamer cracked over a period of time. No installation, no problems I just recently used it and works perfectly! Thank You!
We ordered element support 3 times and all three times it came broken. The part is made of porcelain and is fragile , representative asked warehouse to pack it in the box and part still came in envelope. Requested refund and ordered directly from factory.