Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Plastic clip broke holding lid for pantry compartment
Unscrewed all related parts and also took out drawers and glass shelf. Reused plastic slider which raps around right corner to the back wall of the unit. Make sure to remember how this plastic slider fits into the new end cap, it is a little tricky putting it back without cracking it. Suggest take a digital picture as to how it fits together before taking the slider out of the old end cap. Reinstall same way as you took it out. Good time to clean while everything is out of the bottom of the refrigerator.
Removed the door and replaced the broken door closure bushing. I had courteous help and responce from Parts Select people. Excelent turn around time on parts delivery.
Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.
I brought you the exploded view of the crisper parts on your website and proceeded accordingly. Besides the three nuts holding the end cap to the frig interior wall the temperature adjustment linkage had to be disassembled on reassemblied on the new replacement end cap. Plastic linkage parts present the problem of breakage, so one must be careful during the disassembly process. Some other type of fasteners for the linkage assembly (screw and nut, ball and socket) would be prefereable. All and all, its a machine. Wtith exploded view, what could go wrong?
Right side endcap - drawer pin broke that the flip up top uses to pivot up and down
I removed the right side endcap and rear thermostat piece behind the pull out drawer. It was fairly quick, 3 screws on the exterior of the end cap and one screw holding in the drawer thermostat. The worst part was getting the thermostat control that connects the drawer thermostat control to the rear thermostat. After playing with the control rod I was able to to snap it in successfully to the endcap with the proper rod connection. The rear thermostat goes in first, then the endcap. Quick and easy. For $23 it would have cost over $150 to call a repair guy ($120 call charge plus parts). Thanks.
intermittent clicking noise; otherwise fridge seemed to be working fine
Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.
Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar. Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars
Looked at the new part to determine what I would need to remove the old part. It was very easy to figure out. I removed the old end cap by taking out the screws. Once the screws were out I popped the side of the end cap off. There is a horizontal piece along the back wall that is connected to the end cap. On the left side of this piece of plastic there is a small tab that clicks into the back wall. On the right hand end cap there is a sliding lever which controls the air in the deli tray. This control is made of plastic and appears to be pretty fragile> By gently bending this lever I was able to remove the control lever and install it on the new end cap. In all it took me about 15 minutes to complete the entire job. Very easy.
Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??
Seal would not stay on, letting cold air out of ice maker - did not make ice.
The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.
Clicking & popping for about 30 sec. when compressor starts
As shown on the YouTube link sent with email receipt. Removed back panel. Removed the clip securing the parts with long nose pliers. Unplugged the old, replugged the new. Replaced the clip to secure.
Unfortunately, the capacitor and relay did not fix the loud clicking issue.