Models > KERC500EAL4 > Instructions

KERC500EAL4 KitchenAid Range - Instructions

All Instructions for the KERC500EAL4
61 - 66 of 66
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Parts Used:
Main Power Terminal Block
  • Christina from West Des Moines, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Wires are to short.
One screw on each of the two cover plates removed, then element is pulled out enough to get at the connections. These are small blade connectors that slide off, two on each side, so 4 all together. The problem for me was that on one side the wires were to short and as soon as the blade connection was released the wire pulled back through the hole and was difficult to retrieve because it was hiding in the insulation. If I were to do this again I would use a small zip tie around the wire before disconnecting it so I would have something to pull it back out with.
Parts Used:
Dual Broil Element
  • Timm from Orleans, MA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Outer circuit of Broil Element was open
I received the replacement broil element for my Kitchenaid model KESH307 range 34 hours after placing the order online with PartSelect.com! I had previously removed the old element and verified that the outer circuit was open. I did this without removing the oven door. I realized that to install the new element with the door on would require me to have 5 foot long arms and a very flexible 2 foot long neck.

Turns out there are at least 3 different styles of door mounting in the Kitchenaid line. I found the correct one for my range, and when the new element arrived, I had the door off in a jiffy. Enlisting my spouse to hold the oven door switch so as to keep the light off (It shown in my eyes.), I installed the new element with minimal difficulty. It took me about 20 minutes.

Thank you PartSelect for being there and for the really quick delivery.
Parts Used:
Dual Broil Element
  • Harry from Salem, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
interior glass broke
removed oven door from stove. Laid door on work table. Took screws out of the bottom. Flipped each layer over until I got to the interior glass. Removed broken glass and installed new glass. Flipped pieces back in place and put screws back in. Placed oven door back on stove. Easy!!
Parts Used:
Interior Door Glass
  • Sylvia G from Harrisville, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lower Oven Element for Whirlpool Oven
Removed the element by using a basic screw driver...two screws. Detached the slip on wire attachments (don't know what they are called). Re-attached new element and screws. Very simple. I was hoping elements were a little cheaper, but I was impressed with the speed that Part Select delivered my new element. I'll use them again.
Parts Used:
Bake Element
  • Gerald from Castroville, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Door wouldn't close tight
First of all I couldn't believe parts arrived next day. Parts solved the problem I was reluctant to believe new hinges would solve the problem. I installed the hinges in about 1 hour but I had door apart previously so I knew what I was doing. Now my wife is speaking to me again and she threw the wooden spoon away that she used to hold door closed. Just spent $100 dollars and saved $1600 thanks guys.
Parts Used:
Door Hinge - Left or Right Side
  • Dale from Port Tobacco, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KERC500EAL4
61 - 66 of 66