Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
didn't eject icecubes
R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic. Very Satisfied, Ron Martin
Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) Then I put the new valve in, put the cover back on the refridgerator and was done. total time 15 minutes. My wife says I'm the man.
The plastic ring that is the connection between the drive motor at the back of the freezer compartment to the auger in the ice bin shattered when my wife was dispensing crushed ice.
Part selects cataglog for parts selection was very easy to use and the online service and delivery was great. When I got the part, it was not apparent on how to remove the auger so that I could insert the new connector. There were about about 8 visible screws, with star drive heads that I fortunately had a screwdriver that fit, and I could not tell if I had to remove all of them or only a couple. I ended up removing all, but still could not separate the dispenser portion which held the front of the auger from the back of the ice bin. I finally figured out that the dispenser door trip lever had to be disconnected and I almost lost it when I removed the metal clip that attached it to the outside of the ice bin when the spring loaded lever tried to unwind. I managed to hold it in place, separate the dispenser holding the auger from the rest of the ice bin and replace the connector. I them got the pieces back in place and was able to refasten the spring loaded lever and then replace the screws. If the spring loaded lever had unloaded, it would have been tricky to try to replicate the amount of turns (load) on the spring tension.
Removed everything from inside freezer compartment (food and shelves) Removed inside backpanel that covered the coils. At the top of the coils is where the thermostat was attached. Removed old one and installed new. Has been working since.
I have replaced the circuit board, the condenser fan motor but the unit still will not feeze correctly. The bottom of the unit freezes but just barely cools the rest of the freezer and ice box. Have you got any other advice that might help. This is a side by side unit. What else could be the problem. It seems that the fan is not working correctly or it is stuck in defrost mode. The coils where the fan is seem to be icing up but it will not let the fan work. THanks for your help, David Wilson
First I removed the back cover then removed 3 nuts holding the motor. Next I removed the two wires. Next I attached new connectors to the wires and installed the new motor and everything worked perfect!
Service and shipping were fantastic! I would definitely use Partselect again!
The old ice maker was leaking water when it filled freezing the ice in the accumulation tray into one big lump.
First, I read the instructions that came with the replacement ice maker, which I found confusing because they were apparently written to be installed in some other make of refrigerator. However, after removing the white plastic cover on the new unit and insuring that it was identical to the one that came with the refrigerator, I removed the old unit by first, removing the bottom screw that held the unit to the side of the refrigerator. Then, I loosened the two top mounting screws. slid the unit up and pulled out and away from the side of the refrigerator. Then, holding the unit in my left hand, I pinched the two plastic tongs on either side of the wiring harness where it attached to the outlet at the back of the refrigerator, took the ice maker out of the freezer compartment and set it aside. Then I located the water regulator screw on the right side of the new ice maker and turned it one complete turn clockwise to reduce the amount of water that would fill the unit. After reinstalling the white plastic cover on the new ice maker, I saw that the wiring harness that came with it would not fit my refrigerator's outlet. So I removed the wiring harness from the old ice maker and installed it on the new one. Then I connected it to the outlet at the back of the refrigerator, slid the ice maker over the two top mounting screws and then pulled down to seat the screws. Next, I used a small torpedo level to level the ice maker both vertically and horizontally. This required placing several flat washers behind the metal mounting bracket at the bottom of the ice maker and the refrigerator wall. Once I had leveled the new ice maker, I tightened all three screws and shut replaced the ice receiver tray. Works fine.
My icemaker started leaking water into the catch basin and turning my ice into one big ice burg.
Well folks I put up with an ice burg all summer when I really should have took the time to fix it. You know how it goes though. You get so busy you just put it off. Well don't put this one off because this is just how easy it went. I came home one evening and wanted to make a drink to relax but that big glob of ice was there waiting for me. I took a crewdriver and beat it down so I could pull the catch basin out. Having looked it over for a minute I grabed a nut driver and took three of the screws out that held it in. I unpluged the wire and bingo it was out. Maybe five min. had elasped. After taking the unit out I notice how the non stick surface was coming off of the tray and that explains the black pieces that were getting into my ice. Getting the model number off the back of the fridge and writing it down I went to my trusty lap top and did a quick search for a ice maker for my Jenn Air refrigeraton and blamo...! Part Select came up and I put the part number in their search engine and bingo again there it was, my part. One quick order and in three days it was right there by my door when I got home. Now i'm so excited. I went into the house and didn't even chage out of my dress clothes. Within five minutes it was in. Now I just had to wait for the timer to do it's thing and sure enough, I awoke the next morning to a whole tray of beautiful ice cubes. Wow no more ice burgs. The moral of my story is I spent so much time hacking out that glob of ice and for fifteen minutes of my time, I could have been siping on cold ones by the pool but now old man winter is pressing down on me and I guess a lesson learned was a lesson earned. Fix it!
1 screw remove assembly. Unplug cable harness and remove old cover and wire arm. Replace cover and wire arm and attach wire harness on assembly end. Re attach using screw removed in first step. Plug in wire harness. Making ice within 30 minutes.
My old icemaker lost some of the nonstick surface and the ice didn't want to come out
I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!
The Shaft of the Auger Drive Motor Became Stripped
I removed the one nut screw holding the Ice bucket shelf then removed the Ice Auger Container. Then I lifed the Part containing the Drive Motor. I removed the electrical connection which just plugs into the fridge. Once the Drive motor and container was out of the fridge I removed 4 screws and the Drive motor was out. I disconnected 3 electrical connectors and connected them to the new drive motor. Then replaced the motor and connected the 4 screws. I then installed the yolk on the drive shaft and then put the drive motor container back in the fridge and reconnected the electrical. Installed the nut screw and I was done.
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.
First pull out frig and unplug. Shut off water valve. I just had to remove two screws to disconnect unit from bottom rear corner of frig. Pull element out just a few inches and disconnect the plug that feeds it electric. Disconnect water hose and reattach to new unit. Reconnect electric plug and reinstall in back of frig, securing with two screws. I have an older appliance, so I had to jury rig a bit when reattaching new unit by drilling two new holes for mounting. Also, I had to buy a new water hose because the old part would not accept the standard female end of the hose to connect to. Home Depot has the standard icemaker hoses with two female ends. These two glitches would probably not apply to a newer appliance, but anyway, it's cranking out the ice just fine now! Sure I saved alot of money, even with the extra $10 investment for the hose.
