Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn't heat
First I unplugged the stove. I gently removed the two screws that hold the old element in place. I snipped the wires and then twisted the new wires with the stove wires and placed caps on wires. GENTLY replaced new element with screws. DO NOT OVER TIGHTEN. Then I tested the oven after I put it back together and the oven works perfectly.
All it took was for my husband to remove the screws that held the part in place and disconnect the two wires. He then replaced the part, connected the wires and screwed the screws in. We turned the oven on and it worked perfectly.
This is our second part that we have ordered. The frist part was just as easy as the second.
Remove the sheet metal that covers the burner and the igniter. For me this was two screws located in the rear of the oven. Two 1/4 inch screws held the igniter in place. I then cut the wires on the faulty igniter as close to the porcelin as possible. I cut the clip off of the new igniter and stripped the ends of all 4 wires, splicing then together with the ceramic wire nuts that were included in the kit. I fed the excess wire to the rear of the stove and reattached the new igniter to its mounting bracket. Replaced sheet metal. Plugged the unit into the outlet and away it went. Worked great.
The repair was pretty straight forward. I simply removed the old igniter, then I snipped the wires. Using the included wire nuts I spliced the old wires with the new. The longest time was spent looking for my wire strippers. I must say that the customer service was very quick and responsive. I received the part but it was broken. One call to customer service and the new part arrived the next day. Great job!!
The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.
Ignitor would glow at orange but not white. Not enough heat to open valve to let gas run
Got the general idea off a u-tube video. Very simple and would have been even easier had I used a 1/4 in nutdriver instead of socket. Removed 2 screws (flathead) on the lower cover of oven. Removed 1 nut holding shield. Removed 1 nut holding protective trap door on rear, pulled coupling through hole and disconnected. Removed 2 nuts holding ignitor. That's it. Replace everything in sequence and your done.
Oven wouldn't light. Ignitor wood glow but didn't have enough amperage to open the safety valve to let the gas flow
This was relatively easy repair remove the bottom tray of your oven remove the screws from the two guards remove the old ignitor replace and reinstall in reverse
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
removed lower broiler pan so i could see burner igniter. removed the heat shield in front of the gas valve. (1 screw). started oven. no response from igniter. no gas flow at all. if igniter is bad it will not allow gas to flow. ordered new igniter from parts select for my oven model. got it in a couple of days. it wasnt exactly the same as the original, but was compatible. it came with its own connector, but didnt fit. i had to cut it off and splice in the original connector. i had to remove the burner tube to remove the original igniter because the wire was routed around and behind the tube. it just took a couple of screws to remove it and it pulls right off. this is all accessible on the top of the broiler drawer. installed the two screws on the new igniter and plugged in the connector. started oven and igniter started glowing bright immediatly. oven burner lit off within a few seconds. everything working like new now.
At first I didn't believe it was the igniter due to the fact that it was lighting up, but after reading some of these post, I thought I would give it a try. I accessed the igniter from the broiler drawer after taking out the pans. I removed two bolts with my nut driver and disconnected the wires at the plastic connector after removing the heat shield with a phillips screwdriver (1 screw). I also had to remove a clip to get the wires to pull threw the back of the stove. Here is where the fun began...While waiting on the part to arrive, I decided that it would be a good time to thoroughly clean the entire unit. During this process, I lifted the top of the range to far and cracked both front burner gas lines. After running around town trying to find the gas lines with no luck, I returned home and ordered them from PartSelect as well. The igniter arrived one day and the gas tubes the next. I reassembled the unit and everything works like new, thanks to PartSelect. One other note, when my igniter arrived, It had the exact same electrical plug that my original one had. Some of these post said that you would have to cut the connector off and use the porcelain wire nuts provided. The parts I received were manufacturer parts, no off brand replacements. Again Thank You PartSelect.
I first removed the oven door. I then took out the racks and removed the oven bottom. It slips out easily however, you need to take the door off. The burner cover came next. I used the 3/8 nut driver to remove the four screws. This exposed the burner and electric igniter. Two screws hold the burner tube in place. I recommend removing the burner tube due to the screws holding the ignitor will more than likely need to be cut off. Once the tube is out and you have disconnected the plug for the ignitor you will need to check the voltage at the plug (120 VAC). Place the voltage meter test leads in the oven side of the ignitor plug and set the oven to heat up. If everything is OK the meter should read 120 Volts AC. Turn the oven off and remove the leads. Take the old ignitor off the burner tube and replace it with the new ignitor and plug it back into the oven. Push the plug and wires back into the hole in the burner well and put the burner back in the oven well. Once it is all back in and bolted down try the oven again to verify the ignitor works. Replace the remaining oven parts in reverse order of removal.
I removed the two screws that hold the element in place then I had to splice the wires because the connector was not right and used the two wire nuts that came with the unit .
