Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.
Opened the top section of the stove. Re-routed wires to be connected from the speed control device into the new cord. And done. Put everything back thogether.
Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.
We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.
Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.
This Jennifer-Air cooktop has a black Schott Ceran surface. I unplugged the unit and disconnected the vent duct then removed the unit from the cabinet and shifted it 90 degrees to gain access to 10 screws that hold surface to body. Connections for replacement burner are slightly different than the original. I photographed wiring/connectors them removed the old burner. I removed mounting clips from old burner and installed them on the replacement (required two small tapping holes in aluminum case of replacement burner element). Installed new element and attached connectors (wires). No joy, outside element still did not heat - placed a dual element switch on order (have not received it yet). To be continued.
I carefully removed the disgusting old filter and took straight to trash. I then used my wet/dry vacuum to clean the rest of the loose debris from the area where the filter area is located. I used a clean, dry cloth to wipe the remainder of the material away and then carefully lowered the clean new filter down into it's new home. So easy, it took longer to type out these directions :)
The dual surface burner would come on and go off intermittently when the switch was turned to off.
Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.
1. remove corlan cover from base of unit 2. study original wire pattern of old burner and switch; write down pattern on paper 3 gently remove wires with needle nose pliers.4 replace with new burner and switch with color coded wire pattern copying the original wiring 5 reinstall corlan cover on base. remember to shutdown cooktop from either circuit breaker or fuse in order not to electrocute yourself while working remember wires are live until shut down from main source of power