Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Latch Asembly Broke, Door wouldn't close properly
The door wouldn't close and it thought it the sensor was constantly open so it would turn on even if the door was wide open. Took the 10 or so torx screws off and removed the cover. Lifted the old assembly out and had to use pliers to get the wires detached from the door sensors. Attached the sensors to the new assembly, replaced the cover and screws and that was it. very easy fix.
The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.
I removed the shelves out of the dishwasher unsnapped the old parts and snapped in the new! Replaces the shelves and it is washing like a new machine! Thanks!
Cups and glasses on upper rack were not getting clean.
Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.
The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.
After only 2 years, the Amana dishwasher door began to stick severely. If finally stuck so bad that I had to break the handle to get the door open. The replacement latch and handle fit perfectly and it only took a few minutes to get the screws off of the inner door panel to access the broken latch.
Removed inside cover. removed part. disconnected switches. plugged wires onto new part. placed part in. put inside cover on and screwed down. Note: be careful of the bottom of the inside cover.
plastic in silverware basket cracked so utensils kept falling through/getting stuck
The basket did not include the handle (something I didn't notice when I ordered it). I simply removed the handle from the old basket and placed it on the new basket.
Having utensils falling through was really getting old. This was $25 well spent.
da basket don't come with rections so you gota figer it out yor sef. I tride pullen the handle off and it work then I tride pushen it on the other basket and it work to. Then i tride swapen dem and it work so thats how ya doit
First I removed the screws from the inside of the door exposing the latch assembly. Removed the old part and installed the new assembly. Don't screw it on to the door untill the cover is on again. First I ordered only the latch without the handle. Found after opening it up the handle was broken on the inside so had to order the assembly. It's a piece of cake to install. If you're having touble opening the door don't think because the handle looks ok from the outside it's not broken.. probably is. Partselect.com is the greatest company to deal with. I'd recommend them to anyone and have. Sam
Taking the upper and middle dish racks out, I reached in and pulled out the old parts, then popped the new ones on. All of the ususal tips for our problem weren't cutting it, so we finally figured the seals at the back of the dishwasher were not effective in keeping the appropriate amount of water pressure in the spray arms. The rubbery seals had been degraded by harsh detergents. We ordered the new seals from your company after a phone call to verify we were choosing the correct parts and easily put them in place. Now our dishwasher does what it was designed to do! And less than $40.00 including shipping! We did not need a new dishwasher.
After receiving the latch assembly, which arrived rather quickly, I found the handle itself was not enclosed in the package. Therefore this repair was delayed and after several calls to the 1-800 number I was informed the company had discontinued the distrubution of the handle. They offered a full refund, however I'm still waiting for the return labels so as to ship the latch back.
Now on the brighter side, the company representative put me in touch with a local distributor that did carry the latch/handle assembly as one piece and for a lot less money.
For those who are attempting the repair, don't worry, It was very simple. Just remove hex screws, lift the inside panel, unplug the two connectors and insert the new assemply.
Must say my wife was very happy to have the dishwasher up and running again.
