Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bake element wouldn't heat
Removed the two screws that hold the element in place, then I disconnected the two wires and pulled the element out. I ordered the part and received it within two days. It was very easy to install. My oven was tunning in less than half an hour.
Bottom element burned up and it was a little scary. Never seen this happen.
Un plug the power first.
Took the old element out and removed two nut holding the element in place. Remved back access panel on the back bottom of the unit. Disconnected wiring to part pulling the clip off of the connector.
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
One of the electric range heaters could no longer be controlled. It heated up for no reason.
Pulled the range away from the wall. Took two screws off of top cover with 1/8th socket wrench. Took small Philips head screw off the top, just leaned the cover away from the top. It still held in slots at its bottom so no need to drop it away from the range. Removed the dial from the front exposing two small Philips head screws. Removed screws, and pulled the comptroller away from the rear of the range. Held the new one in the same position as the old one and removed one connection at a time, and replaced them into the new part. Did everything in reverse to put it all back together. Believe me, easy as could be and you just saved $200 repair man cost. Part matched old part exactly.
Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.
This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.
- remove door from range following the basic guide to removing any range door. - place door on work surface with the outside facing down. - remove three 1/4 socket screws from bottom and two star screws on top. - Flip door over, remove outer door panel and set aside. - There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside. - Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed. - Remove the remaining 1/4 screws holding the aluminum shielding. - Remove the shielding being careful not to disturb the insulation around the window. - Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom) - Set the new window in its place. - Reverse the process by replacing the aluminum shield, hinges, than internal glass pane. - Set outer door on top and holding everything together, flip door. - Tighten the two star screws on top and the three 1/4 socket screws on the bottom. - Replace door. Don't forget to lift up those hinge tabs before trying to close the door. All done. Pat yourself on the back for a job well done.
I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.
Broiler shorted out looked like a 4th of july sparkler.
Ordered on Tues got part on Thurs used a nut driver removed 2 screws holding element in top of oven,then removed the 3 screws holding the element and thermostat to rear of oven pull about 3 inches of slack, removed the blade plugs from element placed them on the new element and assembled it. Took abou 30Min. Easier if you remove the oven door!
First thing I unplugged the range. Then I unscrewed 4 screws in the back of the stove to take the back cover off. Then inside the oven, I unscrewed three screws to lossen the element. Then disconnected the two wires from the element.
Then replaced the old element with the new one going exactly backward as mentioned above finishing with plugging the range.
Actual temperature in oven was not consistent with the temperature setting
I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.
First, UNPLUG OVEN. Then, remove oven door and place stove on work bench! JUST KIDDING!! Honestly, the repair would be easy if that were possible.The hardest part is kneeling, standing, hunching over, twisting your body holding flashlight in your mouth, etc...THEN, trying to re-attach wires screws etc. The repair is straight forward. unscrew all screws holding element in, pull element out about 6 inches, detach wires, and re-attach. Simple right? Maybe if you're 1 foot 2 inches tall or have 6 foot arms
