Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice Maker Door fails to close
1. Remove outside panel (snaps off) 2. Remove Control panel 4 screws 3. Remove Solenoid by taking out 2 bottom screws 4. Remove solenoid weight from crank lever 5. Place new solenoid weight from crank lever 6. Insert weight in solenoid 7. Place back 2 bottom screws solenoid 8. Place back Control panel screws 9. Snap back into place outside panel
ice dispencer door will not closeremoved hte control panel
removed the control panel ,using a paper clip, removed five screws, disconected wire connector, and removed the solenoid. reversed procedure to reassemble. ordered the part one day and received it the next day. Thank you for the prompt response.
Ice wouldn't come out of door. It backed up in door
I followed the instructions on a posted desctiption. It workded perfectly. Replacing the inner door panel was not as difficult as described. Just start the process with the screws in the middle of the door. Those two screw holes were not slots. All of the remaining screw holes had slots. I installed all of the door screws before tightening any. I workded right the first time.
I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.
Ice chute wouldn't open or shut correctly - rusted solenoid
Replaced rusted solenoid.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
We had problems with the ice dispenser chute building up frost from condensation freezing due to the flap not closing properly. It would clog up completely and often. I had already replaced the flap and spring years ago but it didn't help much. I Googled this problem for my model and found a video detailing how to check and change the solenoid. Sure enough, the solenoid was completely corroded and crumbled in my hands as I removed it. I ordered the replacement part and made the repair myself. The video was perfect in describing. If your refrigerator is well used as ours is, you'll be shocked by the buildup and cleaning that will be necessary as you make this repair. I ended up taking much more of the dispensing assembly apart so I could clean it with warm soapy bleach water. Be mindful as you disassemble or take photos / videos with your smartphone to help put it back together. It took longer to clean than replace the solenoid. Also, be careful if you have an island or other cabinetry close by. If you have to pull the refrigerator out to unplug it, the handles can chip granite edges or the top corners can scratch wood work. We have cherry cabinets that surround ours. I chipped the edge of the granite when I pulled it out and I scratched the wood as I pushed it back in place. Minor repairs but can save you some frustration. Good luck!
The only tricky part was removing the front panel. Releasing the latches required considerable force. The best tool I found was a "jack knife" type Allen wrench set, using the medium size wrench, which fit into the release hole and upward pressure did the trick. The rest of the job was very easy.
First tried just replacing flap/spring and mounting. Still did not work so then order a new solenoid with piston that attaches to mounting. That solved problem completely. Corrosion around piston prevented fluid movement of flap. Easy fix after watching video. Saved a bundle I'm sure. Thanks !!!
The flapper on the ice dispenser would not close after you dispensed ice cubes
Removed face plate, which holds the circuit board. Removed the next section be removing the 4 screws that hold it in place. Then removed the old solenoid, and replaced it with the new one.