Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old motor was not resetting back to proper position halting ice production.
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!
For replacing end cap, LH pantry part: removed large pantry drawer removed two small upper pantry drawers removed glass panel and long braces---all these parts required no tools used 1/4" nut driver to remove 3 screws from broken end cap, LH pantry part and shook it to release it from the refrigerator used phillips head screw driver to remove drawer arms replaced metal drawer arms to new end cap, LH pantry part attached new end cap, LH panrty part to refigerator and finised by using nut driver on all 3 screws. then replaced other pantry dawers, glass shelf, and pantry cover. EASY!
Original bracket foot brake screw hole was stripped and foot brake would not extend
The repair seemed simple, I just needed to remove the old bracket -- 4 screws -- and slip the new one on.
The tricky bit is that the roller bracket holds the weight of the fridge. So in order to make sure that the fridge did not fall over, and to keep the installation point off the ground so that I could align the screw holes, I needed to shim up the side of the fridge that I was working on.
To tap in the shims, I used a hammer and a spare chunk of wood. I ultimately used 3 shims, and kept tapping until the roller wheel could roll freely. Then I knew that the fridge was high enough. After that, it was pretty easy to remove the 4 screws, align the new bracket, and replace the screws. After that, in order to get the shims out I could just extend the foot brake as it was designed, and that lifted the fridge enough for me to easily slide out the shims. After that I just had to level out the fridge by adjusting the two feet.
First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.
This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.
Ordered new drawer -- fast and easy to find the correct part on this site. I also felt that the price was very reasonable. Except for one thing, it would have been simple to slide the new drawer in. The original drawer has a white plastic "face" that is removable. "Removable" is a relative term. It took my wife and I over 20 mins to very carefully remove the face without breaking. One person could not do it --- you need to hold the drawer firmly while another pries the face off carefully. Once off, it was able to be pushed on to the new drawer -- be firm.
I ordered a new crisper drawer from PartSelect over the internet one morning at approximately 10:00am, and the product was delivered, non-express delivery, the next day at about 4:pm. The front coverplate of the old crisper came off easily, and snapped into place on the new drawer easily. The entire repair/replacement took less than 5 minutes. Service from PartSelect, from locating, to ordering, to rceiving the part could not have been simpler or more efficient. A 5 star experience.Thank you.
Watched Partselect video of P-trap installation.Removed water line & back cover& disconnected wires to water solenoid .Removed old drain tube & old problematic rubber funnel. Used contact cleaner to clean rubber residue from drain line and used a little silicone to aide reassembly. Job went well thanks to video.
Lower the filter bottom housing to gain access to the filter. Unscrew the filter and install the bypass cap. Secure the lower filter housing to the top assembly.
I had to cut off the old yoke since the threads had stripped and it would not come off. Once I did that all I had to do was to remove 4 screws on the auger motor and replace it with the new auger motor. Then I put the yoke on the new auger motor shaft and then put the unit back in the freezer. Work time was less than 15 minutes with no problems.
Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!
It actually took 1 day and 15 minutes to fix this problem.
I removed the drawers and shelves in the area around the pantry. I carefully took apart the sliders and plastic parts that comprise the endcap/temperature adjuster. Then I tried to replace the unbroken part into the assembly. At that point I realized that something was wrong and I had ordered the wrong part. So I cleaned and put the broken part back in the refrigerator to wait for the replacement.
PartSelect customer service person was terrific and had the correct part on the way to my home immediately. I don't know how, but it arrived the NEXT day!
THEN, it took me 15 minutes to unscrew the sliders, endcap and replace both. Thank you PartSelect.
A friend dropped a jar of relish on the plastic window and cracked it.
Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece. Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.
Contacted sears home service to perform repair. Quote for repair was $307. 43. ( $196. 90 For labor ,$102. 58 For part) plus $75. 00 For service call. Based on the charge, I refused the repair and ordered the appropriate part from "part select" (733947) (wpl 8201515) motor module for a cost of $81. 84. To my surprise, the part arrived the next day and in 15 minutes the icemaker was in a position to make ice, and has been producing ice ever since. To perform the module replacement, I had to remove one screw with a nutdriver, pull the icemaker out, disconnect a wire harness, replace the module and do the reverse procedure to complete the installation. I saved a total of $225. 59 By doing this repair myself. A lesson learned. . . . . I will always investigate doing a repair myself with the help from the people at part select. Very professional and they sent the correct part the first time.