Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Freezer was freezing but refridgerator was warm. Checked fan and it was not turning.
Unplug fridge. Removed 2 nuts to get the vent plate off and two more nuts to get the motor mount off. Removed fan blade and then the fan motor. I put the new motor in and put everything back as it was. It was very easy. I had items in the freezer, so I didn't turn the fridge off other than to replace the part. It took about 6 hours for the fridge to reach optional temps because I didn't get to defrost and the fridge had to work it out on it's own. If you don't need the freezer then you should turn the refridgerator off for at least an hour and open the doors so the coils can defrost and any ice blockage between the freezer and fridge portion can melt away as well.
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker. 2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,. 3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket. 4.Now take out 8 screws that hold the back panel in place and remove the back panel. 5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Two of the end caps of one shelf and one of another were broken
Ordered the pairs of end caps for both the door shelves. The parts arrived the next day. Opened the wrapper slid the end caps on and attached the shelves to the door. Bingo!!! It was that Easy! Done in less than two days and less than $20. It took me some time to figure out if the parts were right though when I searched online.
Ice maker quit making cubes, instead it made a large block of ice.
Unplugged the fridge. Removed water inlet valve from fridge. Used voltmeter to test for resistance (between 50 and 150 ohms). Didn't pass the test. My original part was 218720400. I ordered part PS468507 from partselect.com. My original part had a "garden hose" coupling so PS468507 fit the bill. This part's electrical connection wasn't angled the same way as the original so we had to finagle it. Hooked the plastic refridgerator supply hose up first. Then screwed on the copper "garden hose" connection to the valve using channel lock pliers. Was careful not to over tighten. Then the fun started. The electrical connector wires were a tight fit between the copper tubing and the refridgerator frame. Did I mention that the electrical connetion wasn't angled the same as the original? My daughter got her smaller hands in there and was able to make the connection. NOTE: Because of the angling issue I was unable to screw the anchor plate to the fridge. I made sure that the valve did not interfere with the fan. Turned on the water and checked for leaks. Plugged the fridge back in and in a couple of hours we had ice cubes. Works like a charm!
Just snapped in the wholes and pushed it down a little bit and there it was. It only took 2 minutes. Very simple process- price was supper and delivery was very fast. Thanks guys- will order from you again
End of door shelves broke & were held on by duct tape for a long time
Since the end caps were already broken I just took them out & put the new ones in. Total time to do this was less than 5 minutes. Great parts, great prices & super fast shipping
Made sure water was going into valve, shut off water to valve, removed it. removed two connections, replaced with new valve, Walla, off & running. Incidentally, rec'd new valve much quicker than I ever expected.
Replace the gasket around the freezer door ($122.00 NEW GASKET)
Moved the old gasket aside to gain access to retaining screws in top freezer door. The new seal in the container we received was twisted, so laid it flat and used a hair dryer (as you advised) to regain the proper shape. Did everything possible, to align the gasket. Opened the freezer door to remove the retaining screws, began to reinstall the new gasket. The top came down both sides well. Attempted to install screws across the bottom, the gasket was so twisted would not conform back into the retaining frame on the bottom of the door. Therefore, it fits poorly. No proper seal. Sincerely, Jesse & Mary(also, the bottom of the freezer door plastic form was very brittle, broke where the screws fit....so we had to make a piece formed like a strip to re-enforce the areas that 'cracked' off so as the screws could align the bottom areas.
