Broken plastic part at top of water fill tube to freezer
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again and installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Remove bottom of freezer by sliding out the gaskets on each side.
Remove back of freezer. 6 screws.
Remove fan cover. 4 screws.
Remove fan. 3 wires to disconnect. 2 screws to take out.
Install the fan. Connect the 3 wires. Fastened with 2 screws. Put fan cover back on. 4 screws. Put back of freezer back on. 6 screws. Put bottom of freezer back in. Slide gaskets in on each side.
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Outer case of freezer was heating up, not making ice (sometimes) turned up thermostat several times (especially freezer)
I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.
Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
First I removed all the screws from the back cover. 2nd removed fan nut and fan blade 3rd removed fan bracket 4th I traced wire to the condenser and disconnected wires from wire nuts. Installed existing fan brackets to new motor kit then reconnected wire nuts to new motor cord Reinstalled fan nut and blade, reinstalled cover, plugged it in and BAM .WORKS PERF!
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easier to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.