Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice maker stop making ice
Looked up the part and found it on PartSelect. I was exactly like the same as the part I had to replace, there for I didn't have to make any new adjustments to the part to fit. I also read the story by others that had the same problem on the website. I had anticipated the part was bad, because no water was getting to the tray. I ordered the part and did the repair pretty quick.
Turned off water supply and electricity. Removed old valve by removing two 1/4 in nut screws and water supply line and the ice maker suppy line. Disconnected the electrical line.Reattached water supply line,the icemaker supply line and the electrical connector. Put valve back into refrigerator and attached the two 1/4 in nut screw. Turned on water supply and electricity. Bled water thru system and now have plenty of ice.
Checked the manuals and found the needed part. Having worked with solenoids before gave me an idea that it was the defective part. The valve would open when water was needed and you would hear this gushing sound. Water supplt was okay and the ice making unit was also working. Bought the part from this website, switched the unit and now the ice maker is working perfectly. This could not have been any easier. Make sure to keep your manuals handy!
not makinig ice due to lack of water flow to maker
Followedinstructions that came with kit. Kit parts were unnecessary as new valve fit in exactly as old one had been. Quick connect for flow out of valve to maker was a surprise as no threaded connection present and no nut necessary; simiply push the line into place. Reconnect water line, check for leaks and refasten back covering. Instructions with kit contained an incorrect drawing of connecting water outflowline; a one page addition verbally gave correct info, but detailed step by step instruction for this one connection was confusing. Otherwise, could not have been easier; surely a do-it-yourself project.
First attempt was difficult. Part was different and instructions applied to previous part that did not have quick connect. Not clear where quick connect was to be used. Result no ice!second attempt used quick connect in reverse connections and now have plenty of ice. Combination of change in part appearence from previous one ,and different from instructions included with new part, resulted in confusion in installation. In the long run, it worked out well.
Disconnect ac power line, disconnect power line going to the water valve. Turn water off atthe cockvalve. Disconnect water line to valve. Disconnect plastic tubing going in the valve. If plastic is old you may have to replace it to keep from leaking at the quick connect coupling. Connect water line and plastic tubling to new valve, connect power clips to new valve. Plug in the refrigertor and turn on water at the cock valve and your good to go
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Original ice maker quit
Shut off water supply, unplugged the refrigerator, replaced solenoid, replaced exterior waterline, made sure there was no ice in the feed line through the back of the refrigerator, replaced interior ice unit, tested for water leaks and let it run over night. Doing it's job this morning. I am pleased with the kit and instructions. Regards Steve
Ice Maker was overflowing into ice bin when filling
Thought we'd try the Water Valve before replacing the ice maker. Ordered new valve online on Saturday, it arrived on Tuesday. I installed it twice in less than 30 mins. Had a little leak the 1st time, so I uninstalled it, trimmed up the water line with a box cutter and reinstalled without issue. No leak this time. Easy Peasy. My husband said "You're good, you." :)
The part could not be installed without home made angles which were attached to unit so that it would only protrude from back of refrigerator about 2" instead of 6".
1. Removed part from packaging. 2. Cleaned part with foodsafe cleaners. 3. Rinsed thoroughly. 4. Dried thoroughly to prevent frost. 5. Placed bin in freezer. 6. Turned on ice maker. 7. Waited. 8. Discarded first batch to clear supply line. 9. Waited. 10. Enjoyed ice. 11. Provided these inductions.