Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bottom trim had rusted, so we needed new piece
Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)
I was so sick of this drawer and I over heard a buddy telling a story about a website that you can get ANY piece for appliances. I take the drawer out, look up the website (partselect.com) look at the appliance diagram and find the missing piece. Order it, get it, install it. My wife thinks I'm a hero and I think I'm pretty cool too.
The trim piece on the bottom of the door was rusted making the unit look really dirty and used.
It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.
Bottom part of the Drawer Glider broke off on both sides of the drawer.
Remove the draw from the stove. Then unscrew two Phillips Head screws ( one on each side). Remove the old gliders. Slip in the new gliders. Screw the two phillis head screws back in. Make sure when you put the drawer back in the stove that you lift the front of the drawer up enough that the lower portion of the new glider is engaged on the side rail of the oven drawer space.
18 year old gas range, just replaced oven igniter, and tried repairing burner igniter
I replaced the oven igniter, discovered the floor of the oven had rusted through, so I replaced that as well. The burner on top of the stove would not light as it was designed, and because the 12 screws that hold the range top and burners in place were rusted in place I ended up buying a new range because removing the screws on the burners proved impossible, even when I tried to drill them out with a lefthanded screw removal tool. I should have just kept lighting the burner that would not light, with a match. That was a repair too far, that forced me to buy a new GE Range and throw this one in the trash. The igniter, oven floor replacement was easy. The burner igniter after 18 years proved impossible. .I installed the 18 yr. old burner grates on the new range, but the drip pans would not fit the new stove. New GE Range instructions were near useless. Do Not trust them, especially the Orifice change details NG to LPG.
the instructions given for this part were not 100 % accurate, our oven door required multiple, dis assembly and was unable to complete the task, local handy men refused to come to assist since the job was already started, it appears I will now need to buy a new oven , I was disapointed in the help because had we known we had the more diffcilult oven, would not have attempted, I did give the correct model and serial number to the person when discussing this part
On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.
Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.
Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim. Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.
Replaced igniter pins but no joy, needed igniter module
Most videos show getting to the igniter module from the front when in fact with this older GE its accessed through the back left corner from the backside. So easy, a few screws and I was in. Quick change out and all worked well again.
