Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
I'm not for reading instructions. So I just dove right in and took the dryer apart to get down to the motor. I gave the dryer a thorough cleaning and replaced the 3 parts I ordered from the online recommendation. Wish I would have ordered 2 sensors and the 2 thermostats that are near the burner. Just so replace beings I was in there. Replacing the parts was easy, found them just by looking for matches to the new parts. Reassembled the dryer, dont think I put a single screw back where I got it lol. And still haven't put the top lid back on due to difficulty. Not sure if I even needed any parts, found a nest in my outside vent completely plugging it. But after a good cleaning and replacing the parts the dryer dries the best it has since we've owned it. The dryer came with our house which we bought 3 years ago and it was 2 years old when we purchased the house, so it is now 5 years old.
After replacing the locker assembly (female) on the machine, The door strike(male) was hitting well below the locker. I realized that the screws holding the door hinge were loose. Tightening them brought the strike up far enough to engage the locker, although it still hits a bit low. That might have been the real problem, not the latch, so check the hinge before you order the latch parts.
Removed top of dryer I carefully removed wires from back of control panel Removed control panel Most of screws hold cabinet together Unhook wire from light on door and sensor on the front panel. Remove the front door and panel together I changed both front rollers on front panel If you have to change rear rollers lift tub up by belt Remove screws on back of dryer that will let you lift out inside rear panel that holds the rear rollers Change rollers and just revearse procedure to put back together
Original lint housing has damage that causes clothes to get caught and tear up
Able to complete install but the lint housing does not allow the lint screen to slide down completely due to the housing lacking the appropriate cut outs/notches. The slit becomes too narrow for the lint screen so it protrudes from the sides. The delivered product does not match the image on the item description, which shows the proper cut outs/notches that should fully accommodate the lint screen. I'm having a similar experience with this reviewer:
John S - February 14, 2022 Verified Purchase Lint screen housing The housing will not allow the lint screen to set completely down because the housing lacks the proper cut outs causing the lint screen to set 1-1.5 inches too high. I was able to cut out the required notches in the plastic so that the lint screen would fit. The picture shows the proper notches but the delivered product didn’t have the notches and does not match the picture.
Will return the item and keep searching for the correct lint housing.
Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.
The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.
To use the new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.
Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!
My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.
Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.
I did not do the repair I hired the propane company to do it . It was too difficult for me.they removed top & front of dryer .removed & replaced gas orfice reinstall all parts that were removed. Install and test dryer IT cost me $91.59 for labor & $24.65 for the part & shipping.If the dryer had a side access near the gas valve it could have saved me the cost of labor. I could have done it myself.
I didn't get to do the repair because despite the model number and the picture being exactly what I needed I was shipped the wrong part and basically told by pets select to shake it off that's your problem not ours.
One of the roller assembly froze up & had a flat spot on it. There for causing the drum not to rotate. Pulled it out replaced the roller & up & running.
1 of 4 Drum Rollers Froze Preventing drum rotation.
Replaced idle pulley wheel, worn drum belt and all 4 rollers (1 frozen) due to dryer age. Site video re general disassembly/re-assembly easily adapted to this model and very helpful with exception of replacement of drum rollers. New rollers received (AGM75510755) were pre-mounted on included shafts. This required removal of existing roller shafts to replace with new shaft/roller units. Site video shows placing a new roller on existing shafts after removing a plastic retaining clip. New roller/shaft assembly is a better option and fortunately I did not order extra retainer clips! Rear drum roller shafts have small carved out space to fit a box end wrench to remove shaft nut. Watch out for sharp edges on internal steel parts!
LG Cothes dryer lint filter screen developed a hole and needed to be replaced.
I ordered the lint filter screen and when it arrived it looked exactly like the old one. It should have been nothing more than remove the old one and slide the new one in place.
Unfortunately, the new screen was about 1/2" wider than the old one and would not fit into the guide. After consulting by phone with your parts expert, we confirmed the model number and serial numbers, and eventually concluded that a design change must have been made by the manufacturer. We thought the only solution would be to also purchase the corresponding filter guide. So I ordered the guide. When it arrived, I installed it - a very difficult installation requiring putting my head and one shoulder into the dryer in order to get the screws out. (A long arm with two elbows would be nice.) After I got the old guide out, I discovered that it was exactly like the new one - 1/2" too narrow for the new filter screen. I reinstalled the old guide and returned both parts.
The dryer filter screen still has a hole in it and I am now waiting for my refund. I have no idea how to solve the problem.
The filter screen part number is 24053607, order number 18265310.
The guide part number is 24145665, order number 18348658.