Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven wouldn't ignite
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Pulled the old knob off and put the new one on. Only thing that was difficult was making sure the knob was the right one because the instructions kept leading me back to a different brand of appliance but since the photo looked alike I went ahead and got it.
Igniters were flaky on 2 burners and almost dead on 2
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the utility drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.
Electronic spark ignition would not ignite intermittently.
The spark moule was accessed by removing the bottom storage draw and removing the 2 phillips screws that held the spark module bracket to the frame of the stove located on the rear right side of the draw opening. The new module did come with new spade connectors that reqires cutting the existing connectors off and splicing and crimping the new connectors to the wires for each of the four burners depending on the model stove. Also I had to use zip ties to secure the new module to the original mounting hardware since the replacement module is not a direct fit. Each of the four burners now instantaneoulsly ignite when turned on. I will buy from Partselect.com in the future. Thank you.
I thought that the initial problem based on the users manual may had been the thermostat. Removal of the old unit and installation of the new one was quite simple. The only time lag was cleaning some of the surrounding areas of the oven as worked progressed. As it turned out though, the problem wasn't the thermostat, but rather the igniter. But, that was a fairly easy job as well!
First I took the new gasket out of the plastic bag to make sure it was the right size. Then I proceded to take the old gasket out by pulling it with a long noise pliers. Then I took the new gasket and went around the door putting the pins in the holes that, the old gasket was in. That,s about it.
The oven igniter lit up but the valve wouldn't release the gas to ignite.
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.
I was tired of guessing the temperature on the oven in my apartment so I decided to look on-line to see if I could find a replacement. I couldn't find the exact Model Number to the old stove so I just took the old thermostat knob out and looked for pictures on the PartSelect site that matched up. I found one that was almost an exact match so I decided to take a chance and order it. I was so happy when I received my replacement. It was a perfect fit. All I had to do was take the old knob out and put the new one in. Thanks PartSelect!
Igniter insulation had cracked and spark was shorting out on the flame holder whatchmacallit.
The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter. There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.