Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you
freezer cold and frosting up but refrigerator warm
inside the freezer compartment, remove four hex head screws from rear panel,lift panel forward and unplug wire assembly from panel. find old defrost thermostat attached to copper tube by clip on back of thermostat, unclip, snip two wires to thermostat, take new thermostat, strip 1/4"of wire from wires in freezer (thermostat is prestripped),insert light blue wire from thermostat and light blue wire from freezer into opposite ends of crimp connector and crimp securely. repeat with dark blue wires. set panel back in freezer,connect plug to back of panel, refasten screws and you are go to go! save yourself the price of a new refrigerator or $300 repair by repairman!
Light Switch too loose so no longer triggered by the door.
Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.
I watched the video on how to change the defrost thermostat. I removed the back cover inside the freezer then I pulled off the old defrost thermostat and then using a pair of wire cutters I cut it off and then bared a little of both of the wires and then slid the heat sherink and wire connectors on the existing wires and then slid the other ends of the wires into the wire connectors then crimped the ends of the connectors and then tried using heat on the heat shrinks but still used rubber electric tape over it. I clipped the new thermostat were the old one was and then reattached the freezer wall cover and plugged the refrigerator back in. 24 hours later I checked the temperature in the refrigerator and freezer and both are running a lot colder.
we droppedthe crsper pan glass insert while cleaning the refrigarter and it shattered, the crisper pan ciover lip was chipped.
Easiest way to install was to insert the cover first then insert the glass insert being sure to tilt a little and inert under the shallow lip at the front of the cover. Not a good idea to assemble before inserting in the fridge. When cleaning the refrigerator shelves in the past I took then out of the refrigerator, cleaned them and re-installed in the method above. Just was not careful enough removing when I dropped the glass
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Remove screws from lower hinge and carefully remove the door. In my case it was the lower bearing, flip door upside down being careful to remove anything which might fall off first. I removed the door stop and then pulled the broken bearing out with pliers. Then I pushed the new one in and reassembled it.
Turned off fridge circuit breaker Removed all food from freezer and put in cooler. Removed shelves from freezer Removed ice maker Removed 2 hex head screws Tilted back evaporator cover and tried to unplug connection. Found connection was iced over with a huge block of ice coming from water inlet to ice maker Spent several hours trying to melt and chip away ice without damaging fridge. Finally was able to break up ice with long flat head screwdriver and hammer. Unplugged connector and was able to remove evaporator cover. Cut wires near thermostat and removed Stripped wire as needed and crimped new thermostat in place. Used heat gun and lighter to melt heat shrink. This took a long time and required a lot more heat than expected. Reconnected evaporator cover connection and reattached cover. Reinstalled ice maker Reinstalled shelves. Put food back in Turned circuit breaker back on.
