Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
oven would not maintain temp
. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine. Very Easy!
First I unpuged the Range. Then I removed all racks and bottom tray of oven. The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds. Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE. p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule . THANKS A LOT !
I removed door by opening it to first stop and lifted it up off the hinge's. I removed all screws that held the inner panel to the outer panel and handle. Removed inner panel from outer panel, then glass and insulation, replaced glass and insulation and panel.
Replaced screws and handle,pulled hinge's out to first stop and slid door down on hinge's. This took about 20min. to do, most anybody handy with a screwdriver can do it.
PS: shipping was fast and price was great. Thanks Bob G.
Turn off the gas supply and unplug the power cord. Remove the screw on the back plate for the metal tab that covers the valve. Bend the tab up to expose the valve. Remove the gas line that feeds the broiler with an adjustable wrench. Remove the mounting screw for the valve. Loosen the valve inlet gas line fitting with an adjustable wrench. Lift the valve out. Reverse the steps to install the new valve.
Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...
When the oven was turned on, F2 and F4 came on. Oven wouldn't heat.
After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.
It was so easy, I pushed the panel towards the back and lifted the front up then lifted it right out. I am so glad that you had the part. I ordered it and when it got here, I just sliped it right in, perfect fit! Thank you so much! Cindy Brison
I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.
Remove outer panel first, outer glass and handle come off as one piece. Be carefull to secure as last screws are removed. Remove inner silver panel. Remove broken glass and replace with new. Reaassemble. Around 10 Phillips head screws altogether. Much easier than I thought
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.
Parts came very quickly from PartSelect. Good service.
Remove burnes and top oven glass, , identified cables for each burner. Unpluged cables, remove old ignition module, drill a hole to install new module. Place module in location. I had to figure out what cables were for the right burner as after placing in the same location as old ignition Module it turned out that they were not identical. I did have to cut old plugs to be able to install cables to new ignition module. If the new part came with and adapter to old cables, as old plugs have small connectors, the new one comes with larger plugs. That would have made it esier.
Igniters were flaky on 2 burners and almost dead on 2
The part didn't come with installation instructions specific to any stove/oven so I went by a previous testimony on this website and pulled out the stove, and started to remove the side panel to get access. Well turns out I could have done the whole repair in place because on my Maytag the igniter source is accessible by removing the utility drawer and it's mounted on a small galvanized steel panel at the left side which hides the part directly. The existing spade connectors were the right size for me but I did have to crimp them tighter (which was perhaps part of the initial problem). After installation, the spark is much more powerful and all burners lit first couple "clicks".
oven temperature not reaching setting/temp. up and down
Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.
