With an explosive bang, the spring on one side of the dishwasher door broke. The door weighed like a million pounds and was difficult to open and close.
I found the parts needed on Part Select and read comments by users. I took the suggestion to buy both springs at the same time and the door linkages too. Although they were pricey, the parts arrived in a few days and were absolutely perfect. To my suprise and delight, the entire fix for the broken spring and link and the opposite spring and link were easily accomplished in less than 10 minutes. The links just hook directly onto a small hook on the door and the springs have specially bent ends that fid the linkage and then the adjustable length holes on the door. It made me feel quite manly for about fifteen minutes as I made everyone in the house open and close the dishwasher door several times.
Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.
I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!
Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.
Pulled the dishwasher out and laid it on its back. From under the dishwasher I unscrewed three screws and freed the drain pump from some sort of frame. Then with the pliers loosed the orange clamp that held the black hose to it. Then unscrewed the clamp that held the white hose to it. Then pulled out the purple and white fuse wires. These wires were very tight I used pliers to get them off. The pump was free. Be sure to have a bowl to catch all the water. There wasn't a lot but it stinks. Then put it all together the way I took it apart. The dishwasher works perfectly now.
Make sure power is off. Remove metal toe kick with fillips screw driver. Reach under dishwasher with 1/2" open end wrench and completly unscrew brass nuts from element ends. Then open door and pull element ends straight up. Note: As you pull element ends up (inside washer) you are also forcing the element end wire connectors to come off underneath. The electricial connectors are very hard to get off any other way.
dishwasher racks had become old and plastic coating came off.
All I had to do was take out old racks and replace with new ones. However the top rack did require taking off the part where the water runs through, it was easy though.
I would like to comment on how quickly and efficiently the parts arrived. I placed my order on a monday morning and am pleased to report by tuesday afternoon they arrived, much to my delight.
I had to remove the dishwasher from under the counter. I then had to unscrew (from the bottom) the bolts that held the heater in place. After that I ran into a problem of disconnecting the wires that ran to the heater. I did not want to "force" the wires off and I was unsure how exactly to remove them. I figured out that they are really hard to pull off but there are no clips holding them on, so you won't break anything off. Once I got the wires off, I was able to screw the nuts onto the new heater and put it back into place.
Removed the dishwasher from under the counter, and ran to diagnose the problem. Drain pump ran, but circulating motor did not. Ordered the replacement circ pump / motor assy, and slid the washer back in its hole. When the new motor arrived, I slid it back out, disconnected everything, and drained the water from the bottom. Then I tipped the washer on its side, removed the old motor and installed the new one following included instructions. I did have to use the new wiring harness, and found the new one had only two leads where the original had three. I connected the blue and white leads, and left the original green loose. All in all, it was an easy repair that could be done by anyone with a basic set of skills.
Place spray arm into receptacle. Take nut and screw on being careful not to over tighten. This will strip the spray arm and the same problem will occur. Easy fix!
The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job