Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I needed a new drawer for my refrigerator
I thought I ordered a new drawer to replace the one that was missing. Apparently I only ordered the plastic part of the drawer, not the drawer ASSEMBLY, which required me to also order 2 plastic wheels, 2 wheel axels and a handle trim piece. The sum of all the pieces needed to replace my drawer assembly was going to be $250. That's ridiculous. SO I decided to send the plastic drawer back -- which cost me $70 in shipping. I will not be purchasing anything from PartSelect again.
Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove anything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Remove the screws and detach the cover. loose the spring and unscrew backwards the plastic nut to release the drum. Un ensemble the blades and release the drum and the deflector replace new parts and ensemble again all the parts.
(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!
Ice bin auger drum fins broke off from the main shaft,stopping the production of crushed ice.
Replaced the Ice Bin Auger,I ordered from PartSelect,which had much thicker housing and fins than the original .You remove the clip from the end of the shaft and a nylon nut which is a left hand which is opposite threads from most nuts.Its a good idea to take a picture of how the blades and spacers are ,because if not put back in the same direction their will be no crushed ice.It now works better and quiter than when it was new.
i used the instructions that came with the part and it was really simple. thank you very much. it saved me a HUGH repair bill.we use alot of crushed ice and the part shipped in 2 days. thank you.C.D.L.
One of the light bulbs went out on my Whirlpool refrigerator.
I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.
It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.
Bottom plastic door cam on side-by-side frig worn, and door stop bracket broken.
1. Removed 2 screws on top hing. 2. Easily lifted door and place on table. 3. Removed set screw for door cam. 4. Removed stop bracket. 5. Reversed steps 4 thru 1.
When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.
NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.
