Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
install a new heating element
First of all the instructions with the part were not very plain to understand so I returned to the web site and read some of the other custormers instructions and was able to figure out how to replace the part. Just had to unscrew the back panel and remove the screws from the heating element housing and then I took the screws out of the lint compartment so I could remove the whole housing to remove the screw that held the heating element to the housing and was easy to cut the eletric wire and conect the new wires and twist the new wire cap on and put everything back together. I was so glad that when I turned the dryer back on I had heat. I am 57 year old women and If I can figure of how to fix my ole dryer than I think anyone can. When I can I will order the part for a new timer. And I hope that my dryer will last another 10 years.
According to previously submitted instructions. toughest task was replacing the tiny screw at the bottom of the heating element housing. Felt good to plug it in, start it up and voila, heat. thank you for the part.
Took off the back panel, and with a little prying got the heating element case off (it's on the right of my LE5800XK). Replaced the heating element, put everything back, and voila, works better than before.
Fairly straight forward except for hidden 5/16 self tap screw coming from back side of heat ducting that is welded to drier. You have to remove this by feel and restart by feel which may be difficult for some. This screw holds the element to the heat duct. It has to come out
My son did the repair and thought it went very well. You saved me about $400 to $800 in that I didn't have to buy a new one. You got this part to me in 48 hours and I appreciated your timely manner. Your service is great! Thanks MZ
I removed the back panel and took the 2 screws out at the lint screen, lifted the top back so I could remove the bracket holding the heating element can. After this was completed I was able to remove the heating element and install the new one, I had to cut the old connectors off and wire nut the new connector together. After this part was completed I reinstaaled the heating element can, secured the top back down,reinstalled the the back panel and pluged it in and wa-la it worked. I also wanted you to know that your prices are about $ 7.00 less than a few of the other part sites I checked on line and one of the sites even said that the part I needed was no longer available. I am sure glad that I kept looking and found your site because you saved me from buying a new dryer, thank you and if I get asked where to get parts I will recommend PARTSSELECT.COM. Fred
Took off the back panel of the dryer. Removed the screw holding the drying element in only to discover it would not fit out the bottom of the case holding it because it was too close to the bottom of the dryer. Had to take off the top of the dryer and remove the casing, remove the element, replace it and put the casing back. Not too difficult, only two wires and one screw. Did make a couple of rookie mistakes making me backtrack and redo a few things but nothing major.
Remove the screws from back cover to remove it. Remove the two philips screws of the filter on top of dryer, to open top cover. Once open, remove the screw that holds the heating element housing. Unplug the terminals from heating element. Unscrew the heating element from its housing. Replace the heating element. Screw on the opposite way you disarm the dryer.
Pulled the dryer out, unplugged from wall, removed vent hose and back covers. Poked hole through the label on the dryer frame to remove the heat element case spring retainer. Pulled the element housing out of the dryer and separated the element from the outer housing and did an ohm test. Test showed an open circuit. I found the burnt spot in the element and ordered a new one. Reinstalled with new element and everything works great.
Everything wears out with age. This is the second element I have replaced on this dryer. The time is fast approaching the dryer too will go the way side. For now, though, we just keep her going as best we can. Simple installation using simple tools. Safety first, unplug the unit. Make comfortable room to work on it from behind. Remove the back panel, push the top off and unscrew the retainer. Remove the bottom retainer screw and the two wires on the element itself. All you have to do now is lift the element case off the bottom bracket, remove the old element and replace with the new in reverse order. Viola! Be cautious of your new drying times. It seems a fresh element brings new life to drying your clothes. We have found it has been cut by more than a third time. As a side note; bring the shop vac out to suck away all the lint that accumulates inside. Fire hazard for one, deterant to life of machine also. You don't have to be an electrical genius either. If it comes down to that type of repair....Better call a repairman! =0)
Went on-line, used Youtube to diagnosed heater element problem, went online and PartSelect's name came up-- easily found the element I needed -- the price was so reasonable that I did not feel I needed to price repair. Ordered the part -- part came fast-- no hasles.