Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven door wouldn’t close all the way.
Bought new hinges as that was the obvious problem. Below is the removal, installation process for new hinges. Turns out in my case there was nothing wrong with the hinges. Problem was still there after installing new ones. I found that the metal in the door that butted against the hinges was fatigued causing looseness. I ended up compressing the metal back into shape with a hammer. Problem solved but money wasted on hinges. If you replace hinges. Here is what I did. 1. Open door slightly to where it stops in broiler position. 2. Remove the door by pulling up. 3. Remove two screws in front of hinges that hold them in. 4. Pull range out a few inches for access the remove the side fillers that trim out the stove. 5. Reach in from the side and work hinges out. 5. Pop in new hinges and reattach the 2 front holding screws and the side trim screws. You are done.
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Front 8" burner stuck on high no matter where dial was set.
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Pull out the range...hardest part. Remove back panel. Remove/install switch PS, This is second switch I had to replace. Try making them in the United States.
Leveler screw in. Adjust to height of counter top since stove has lip that rest on counter top. Oven lens cover difficult to unscrew. Use rubber glove to get better grip!
Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.
Oven erratic, not heating correctly, timer beeper sounding
The video indicating •unscrew old sensor, •pull wiring, •unplug old sensor, and •plug in replacement was good until I pulled the old one and saw wire nuts behind the small square hole! After some research, I learned that the nuts COULD come through that small hole with use of needle nose pliers. One of the wire nuts had the edges pinched off (chipped) in the process. Then I learned about ceramic wire nuts, which I'd never previously encountered. Very important if you don't want to melt your nuts! I cut and stripped the end of a disconnect plug to the stove wiring and now I have a plug in place; which, hopefully, I'll never need to use.
light would stay on all the time saying burner was on although it wasn`t
unplugged power took the back panel off unplugged the 5 wires removed knob by grabbing and pulling off took two screws out of front panel removed the switched put new switch in place and reversed the procedure went very smooth know problem at all any one with any kind of ability should change this switch in know time at all
SHUT OFF POWER AT BREAKER BOX! Remove oven door, use nut driver to remove two screws holding old element to back of oven. Pull forward to get wires into oven, remove wire clips from old part and re-attach to new element using pliers. Re-attach to back of oven, replace door. Turn on power and heat oven to burn off coating on new element. Not at all difficult, except for wire clips are at angle to wire, making re-attachment a bit difficult to do. DO NOT LOSE WIRES INTO BACK AS THEY WOULD BE VERY DIFFICULT TO RESCUE IN A JENN-AIR SLIDE IN UNIT LIKE OURS.
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.
First I cut electric power off removed the two screws that hold glass top lifted up and removed two screws that hold element in place. I disonnected the wires and then pulled the element out