Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
left cover for the oven light broke when trying to replace the bulb
Ordered the part. when it arrived-quite speedily, I just unpacked it and put the cotton gasket around the glass and screwed it to the proper place in the oven. Very easy.
Drop in range was in excellent condition until element burst and was getting ready to purchase another range and then I was looking to replace the element and found part select and they were great from the order process and shipping was fast and the whole process was 5 STARS. As far as me doing the repair I watched the video and it was simple for even me. I also replaced the bake element at the same time. Once again I highly recommend Part Select and they are second to none.
Pull out the range...hardest part. Remove back panel. Remove/install switch PS, This is second switch I had to replace. Try making them in the United States.
Oven sensor caused cooling fan to run continuously. Had to flip breaker to get it to turn off..
Left oven off. Located sensor in pdf manual. Unscrewed mount, pulled sensor out to access connector. Disconnected old sensor, checked continuity(resistance) on ohms with multimeter. No continuity; connected new sensor, screwed mount back into place, turned on oven and baked cookies to check operation & it worked perfectly.
Front 8" burner stuck on high no matter where dial was set.
This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.
Replacement part was exact and worked perfect.
Turn off the circuit breaker for the range.
Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.
Pull the bottom of the front panel out about 30 degrees and lift off the top.
Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.
Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.
Took screws out of the back on the side the sensor was on, unplugged it & took out the two screws on the inside of the oven to release the sensor. Put new sensor in place with the two screws & used one of the adapters to plug in the new sensor. Put screws back in the back panel & turned on the oven which unfortunately is still 50 degrees low. Need a new clock with computer which is out of stock & unavailable. I was an electrician for 25 years so didn't experience any problems. It was a cheap thing to try.
With the back removed, replacing the lamp receptacle is straight-forward. Likewise, the door gasket is very easy. However, in order to replace the hinges, you have to remove the burner glass top (screws underneath the front lip), and inner and outer side panels. Also the supplied hinges mounting holes were not threaded so I had to use my own bolts, lock-washers and nuts in order to attach them. Total time, including a bit of cleaning, was 5 hours.
The oven heating element burned out like a lit fuse!
Removed 2 phillips screws, unplugged 2 wires, threw away old element. Installation of the new element was just as easy but in reverse order. Piece of cake!
Very simple fix--unpugged two fittings in the back of oven plugged in the new element and it was done.The Best part was that the element burned out on a Sunday and I ordered the part that day and it shipped on Monday and received part on Wed AM.This is the second time I've had to replace the element and by ordering through Part Select I saved $24.00 versus buying it from an appliance store.
Took two screws out unplugged the element and plugged the new one in and replaced the screws and turned the breaker back on. Works great...Piece of cake..jk
Ordered element and recieved in two days(yea). Removed back cover from unit. Removed two wire slide on wire clips. Then went inside oven cavity and removed two screws holding element intact. The element slid out. Installed element, re-installed two screws to hold element intact. Attached wire clips back on to element, re-attached back cover. Plugged unit back in and it worked perfectly. Eazy-peezy lemon squeezy.
John Johnny on the Spot Home Repairs Fishers, Indiana 317-997-3600