Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The light socket cup could no longer hold the bracket that holds the light cover in place.
I watched a video of a similar model to familiarize myself with the required steps needed. I opened the back and disconnected the power cord and ground wires connected to the removable socket I then removed the lightbulb and removable socket from the oven interior side. I then removed the defective light socket cup and replaced it with the part I purchased. After replacing the removable socket and lightbulb, the bracket holding the light cover functioned perfectly with the new light socket cup. Final steps were to reconnect the power and ground wires to the removable socket. I then replaced the back cover over the light socket cup area. One word of advise. Be very careful when removing and reconnecting the cables to the removable light socket.
Pulled the stove out from between the cabinets, used a blade screwdriver to pop the oven door retainers down and lifted the oven door out, removed the racks. used a 1/4'' nut driver to remove the 5 screws holding the broiler in place. From the time I unplugged the stove from the outlet until I plugged the stove back in was 15 min. I would suggest wearing gloves because the metal frame around the burner element has sharp edges.
I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS LIFTED UP THE SURFACE BURNER PANEL, OPENED THE BACK RANGE COVER, UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS SCREW THE OTHER ENDS BACK WITH NUT HOLDING THE BURNER CONNECTOR
I first pulled the stove away from the wall to unplug and look from the rear. Look at the wiring from the back (you may have to remove 2 screws and the plate that covers the wiring) and take a picture of it if you can with your smart phone - this way when you go to put it back you have a reference. I then removed the oven racks and the 2 little bolts holding the element in place. Wiggle it toward you slowly so the wires don't pull off. It's easier if you use needle nose pliers to get the fittings off, if its hard wiggle the fitting it will come off. I put the connections on the new element and squeezed them tight not to move. I did put a small piece of electrical tape on the connection ends for my piece of mind. Screw it back in and, plug it in and turn on. If the element starts to glow your done, put the cover back on over the wires and slide it back in place. If your kind of handy you can do it.
couldn't get exact fit--out of production. mounting bracket at back of range for new element too small. took bracket off old element. cut down bracket on new element with tin snips, drilled holes thru it and old bracket and screwed together. at this point the new element was to long & touched oven door. removed spacers that came with new element (used old support to attached to roof of oven) and pried elements apart (which made element wider & shorter). working good.
After years of great service the bittom bake element went up like a sparkler in two locations. Looking back, the heating effeiciency had probably dropped off subtly over time too.
The repair was very easy and your video was extremely helpful. Especially regarding pulling the oven out and removing the back wiring cover to get to the spade terminals, rather than trying to do it all from inside the oven. Added bonus was that I got that pocket for the oven cleaned out like new! Eww! Pulling it out also gave me enough reach without having to remove the oven door (didn't realize you cold do that). Best part though was your mention that GE often DROPPED the zeros in their parts numbers. Couldn't locate the part on any website until yours noted this. so.. you got the sale. Went back to GE's website, located it and found your quality part was also less expensive! 11 minutes start to finish, quick shipping and works great! I'll be back! Thank you!
Having done this replacement before, it was very easy. My advice to anyone having a similar case is to approach the connections from the back of the stove by removing the center back panel for easy access to the connection terminals.
1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.
After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son had spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.
