911334 - Instructions

I only wish I would have taken the drawer out first to get at the wire connections. Instead I tried to get at them by trying to remove all the layers of sheet metal at the bottom of the oven - to no avail. Once I took the drawer out and saw the connections and bolts to remove that held the igniter/gas diffuser there was no problem. The new igniter does not come with the connectors on the ends so I simply cut off enough wire from the old one and used the wire nuts that came with to splice the wires. Simple reconnect and now we're "cookin' with gas" again.

Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.

I followed the other instructions folks had left, and things went very well. I did unscrew the mount to lift the entire flame assembly out, which made getting at the screws for the igniter much easier. Once I had done that, I clipped the wires close to the old igniter, one at a time, then connected them to the wires on the new igniter. The part came with ceramic wire nuts for this, which I was glad for because I wasn't clear how best to connect wires in a heated environment. Put everything back together and it worked perfectly.

Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.

Could not get at the screws holding the igniter to the buner, without removing the burner.

I removed the igniter by first removing the oven racks then the oven pan and oven catch pans. I open the lower draw to the oven and removed the drawer. I reached back under the oven and clipped the wires that run to the igniter and striped a half inch of plastic to expose the wire. I removed the igniter from the burner and replaced with new igniter. I then fed the wires back through the hole the cut wires came out of and used the wire nuts supplied to connect. Replaced other parts in reverse order and tested. Works great.

First had to disconnect the old igniter by removing screw with a small wratchet wrench. Then pull out approximately 3" of wire from the old igniter, cut off old igniter, attache replacement igniter with supplied wire nuts, shove excess wire back into wiring compartment and then attach the new igniter.

The repair was easy and not very time consuming. It didn't take very long to fix the problem and thanks to this site, I was able to save the money I would have spent if a repair technician came out to do the same work. Now I can afford Christmas and cook too!

Troubleshooted ALL possible causes and after perusing the owners manual and PartSelect blogs. Can't say it enough, people!! Do your homework- there are 3 possible parts that can cause the oven not to light; Igniter, gas safety valve, or thermostat / power switch assy (oven control knob).
SAFETY FIRST...UNPLUG the stove before performing any of the following electrical circuit checks (besides voltage check, which is ONLY for those qualified for electrical circuit maintenance)

Remove oven door by opening slightly and pulling straight up- it will slide right off the hinges.
Remove the 2 thumb screws holding the lower oven plate and slide it toward the back while lifting up on rear of plate to clear the front flange and then remove the plate.
The burner tube baffle plate will come right off after removing the one retainer screw (1/4" nut driver).
(Optional)Remove the whole broiler drawer by sliding it fully open and lifting it up by the front end.
Now you'll have clear access to the igniter, which is mounted on the rearward end of the burner tube with two 1/4" machine screws. Disconnect the igniter wire connectors at the gas safety valve and wire harness. Remove it and SAVE the screws for mounting the new igniter!! NOTE: .
Handle the new igniter CAREFULLY!! (don't drop it or bang it against anything solid or the heating element will break).

1) Checked t-stat switch on oven knob - good (closed or 0 ohms when turned on). This verifies you are getting supply voltage to the igniter circuit. Lift the oven top by the front corners until the supports lock into place. Locate and disconnect wires on back of switch and measure ohms across switch terminals.
2) Checked voltage at igniter wire terminals with oven knob turned on (this step ONLY for those familiar with proper use of multimeter and training for electrical circuit maintenance). This verifies the gas safety valve switch is closed and correct voltage is available to power the igniter (120V).
3) Since I had proper power to the igniter wire terminals with the oven knob turned on past 200 deg., that verified a malfunctioning igniter.
4) I chose to solder and heat shrink the wire connectors to the new igniter but you can use the supplied ceramic wire nuts. Be sure to leave enough wire length when you cut the wires off the old igniter. Mount the new igniter to the bracket with the screws you saved and be sure to snug them good but DON'T overtighten and strip the threads!! Connect the two igniter wires to the gas safety valve terminal and the harness connector. Make sure the connections are snug!!
5) Reinstall the burner baffle plate and lower oven plate.
6) Remount oven door and turn on oven past 200 deg. The igniter element should glow bright red after a few seconds. Gas valve should open and burner will light a few seconds later.
NOTE: Make sure the gas cock for the oven (on the side of the main gas regulator valve) is flipped to the open position or gas will not flow to the oven burner. The main gas regulator valve is located under the range top toward the rear (trace the gas lines if you can't locate it readily)

I had to replace the ignitor. The wiring was simple. Just had to connect two wires. The difficult part was removing and replacing the ignitor. It is suspended by 2 screws that are very difficult to access.

I removed lower drawer, removed oven door,
took out rear screws to oven pan,removed screws that attatch ignighter to oven wall,disconnected wiring and removed old ignighter. reversed process to install new part. total repair time was about 20 minutes. Also take into consideration that i am a building contractor familiar to appliance repair etc.

Removed bottom drawer removed door and racks and bottom shield.disconected two leads from igniter . then struggled to remove igniter. after ordering part readf comments from other men and the man who said he removed the burner hit it right on the head after the part arrived the very next day after ordering it i removed the burner attached pig tails and had part installed and stove back together in 15 minutes. thanks good experience

The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.

well part was correct .Got it fast son installed it so do not know what tools, But at last one think i did clean under the stove, which was needed. Would do business again if needed.
Thank you

Removed oven bottom panel. Removed lower drawer to access old igniter. Had to take a cover panel off to expose igniter. Unscrew two screws to remove igniter which was a bit awkward to reach. Then simply put new one in its place.

I open the oven, then pulled out the racks. I went on to remove the bottom pan by removing 2 screws from the back.. I then removed the broiler burner and disconnected the wires from the relay. I unscrewed the igniter and replaced it. I stripped the wires and connected the old connectors using the ceramic wire nuts. I put the burner back in place and connected the wiring.. I then trested the unit to make sure it worked . . .it did. I replaced the bottom pan and racks and once again made sure everything was working right.

Job done.