91130465690 Kenmore Range - Instructions

This was a real easy repair. The key is to remove the door (by lifting straight up) and remove the bottom drawer. Then take all the trays out of the oven, using a screw driver remove the bottom pan that hides the burner and igniter. From underneath the oven (ie drawer space) use a screw driver to disconnect two screws that hold the burner assembly against the back wall of the oven. Then remove the one screw from inside the oven that holds the burner assembly (its close to the door area). Unplug the two igniter wires from underneath the oven and then lift out the entire burner assembly. Take off the two screws that hold the old igniter to the burner and replace with new igniter. Make sure you mark the wires when you remove them because you need the connectors on the end for the new wire. Then give yourself plenty of wire, cut the old wire off the old igniter and using the provided wire ties join them to the new igniter wires and reconnect everything. Sounds complicated but it took me about 20 minutes and its really an easy repair. Good luck.

This oven is from 1993 and a lot less complicated than today's models probably are. The first things to do are to remove the oven door and broiler pan. On this model, the oven door simply lifts off the hinges. Once these are gone, you want to remove the oven floor. To remove, locate the two screws at the back of the floor. After removing, lift the floor up and towards the back to pull the floor tongue out of the groove in the front. This will expose the gas jet and ignitor assembly. At the front of the jet pipe is a screw that holds the pipe to the front center of the frame - it is underneath so you may have to bend over to see it, it can be felt easily as well. Remove this screw, this will allow the pipe to be moved a little later. In front of the assembly is a vertical metal plate with a screw at the right of the mounting the plate into the broiler floor. Remove the screw and slide the plate to the left to pull out another tongue/groove set-up. Now you should see the wires completely and the connection to the air-flow adjuster. There is a small screw in the front of this brass fitting, it does not need to be touched. Turn the burner pipe clockwise while lifting and this should pop the assembly up. The ignitor is mounted to the burner pipe by 2 screws that are found on the bottom of the mount. Remove the 2 screws, this will allow the ignitor to hang free. Be sure to pay attention to what wire attaches to what wire, I marked the left wire so that I knew which to reconnect to after the change over. Remove the caps on the wires if this unit has been removed before, if not then mark the wires on both the replacement unit and the original wires. My ignitor has been replaced before, so I used my wire cutter to clean-up the ends of the old connection before reconnecting the new replacement. At this point, you should be able to fire-up the oven, it might take a moment for the new one to warm up, so give about 30-40 seconds. If the oven fires up, it's then working to put everything into place in reverse order. I like to line up the parts and pieces as I remove so I can just put back in reverse.

Turn power to oven off at the breaker.
Remove access panel to upper control panel.
With the aid of an extension rod remove the hex headed screws succuring the fan to the baffle wall. Remove the fan. Replacement model did not have wire extending from it. So remove wire from original fan and attach it to the replacement fan terminals using an appropriate adapter. Install new fan in original position with original screws. Be sure to reconnect wire in the same orientation as the original fan (right side to white wire). Repeat process for the second fan in the upper control compartment. Handy trick for re-installing hex head screw in deep location....use a small piece of electrical tape to hold the hex head screw head inside the socket driver. After tightening is completed the tape will fall away from the screw.

Check that all wiring connections are back in place and tight. Re-install cover and turn the breaker back on. Test the oven out by heating it up again. It will take approximately 30 minutes to reach a steady state temperature inside the oven so that the circulation fans in the control panel turn on.

I was a bit hesitant to perform this repair but attempted it due to the other write-ups which were very helpful. The repair went very well and was quite easy. There was a suggestion to remove the gas defuser (the pipe thing that has the igniter attached), I believe loosening this defuser made the whole repair so much easer and quicker. Trying to remove the two screws that hold the igniter without this approach would have been very difficult. I was hesitant to do this but removing the 3 screws that hold the defuser in place was not a problem at all.

Removed oven base plate by removing 2 screws and lifting out of oven. Pulled out bottom drawer and disconnected two wires from igniter. Removed 2 screws connecting burner to oven wall. Back to oven inside, and removed screw holding burner to oven bottom. Took burner out if oven. Removed 2 screws securing igniter to burner. Secured new igniter to burner. Reversed steps to put all parts back. Oven works fine.

1. Removed oven door.
2. Removed shelves.
3. Removed oven bottom.
4. Removed pan drawer.
5. Removed the 2 burner mounting nuts at back of oven pan drawer opening.
6. Removed top burner nut.
7. Pulled igniter out from top.
8. Snipped igniter wires.
9. Removed igniter from burner
10. Attached new ignitor wires with the enclosed wire nuts.
11. Attached new igniter to burner.
12. Replaced burner.
13. Pushed excess wire out of the oven through opening at back of pan drawer.
14. Reinstalled burner mounting nuts at back of drawer.
15. Reinstalled burner nut at top of burner
16. Reinstalled oven bottom, oven door and pan drawer.

Unplugged the electrical.Removed the door, removed the oven racks and removed the bottom pan. Removed the wire nuts from the two wires. Removed the burner tube. Removed the Igniter. Installed in reverse order. It was very easy however it was the third igniter that I had to replace in this range so I was used to it.

replaced lights in refrigirator and freezer

removed both screws from old slides and replaced with new ones

Since I'm not very mechanical I had my service manager from work come to my house and fiqure out the problem. By using an electrical meter he found that there was no continuity in the igniter. So being the mechanical guy I am I watched him take out 2 screws that secured the the piece of metal that covers the bottom part of the stove. He pulled that part out and from there it was 2 screws to release it from the back of the stove and 2 more to disconnect the igniter from the burner tube. We ordered the part and it arrived in 3 days. I opened the box and to my dismay it was broke. I called to tell them that it was broke and they ordered me a new one right then. I had that part the next day very grateful for that. I was able then to put it back together myself and it worked. Wife is extremely happy with me.

Removed oven door, warming drawer, oven bottom, oven burner, disconnected wires to igniter. Also, instructions said to turn off gas supply at pressure regulator, {little red lever.} I also turned off main gas supply, and un-plugged power cord. Removing the igniter and replacing with new one was easy. Splicing wires and putting everything back together was also pretty easy. The only problem was when I tryed to open the gas to the pressure regulator, the little red lever popped off. Very cramped area to work in, could'nt get a tool to fit in there. So, I got some nylon string, made a loop, looped it on the notch on the pin, pulled it out and got the little red lever back onto the pin and then was able to open the valve. There is no gas going to the burner if that lever is not on holding the pin out, and you can't put that lever back on unless the pin is pulled out. If I ever do that job again I will not touch the red lever, I will just shut off the main gas supply. It would have been a pretty easy fix if that lever would not have popped off.

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.

ordered parts WB21X5301 oven sensor and 2 WB1X681 screws mine were bad highly recommended slid my stove out also a good time to clean all the years of junk behind it removed screws mine were bad unplug the connector slide the sensor cable through the hole and u are good after cleaning be hind stove slide back into spot reinstall power and code went away tested different temps with temp gauge and keypad and we were good

I just took the old oven racks out and put new oven racks in.