Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Longer time for oven to preheat. Replacing oven igniter solved my issue
First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom cover, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.
had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you
Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.
Removed 4 burner knobs. Unscrewed 6 phillips head screws on manifold.Pulled back manifold enough to remove switch. Removed the Two wires from switch and hooked them up to the new switch. Slid new switch on to shaft and in reverse order, reasembled manifold, screws and knobs.
took of bottom pan and pan above the gas flame off and the igniter off , cut the two wires. replaced the igniter hooked the wires togther, replaced both pans. turned the oven on and it lite
remove bottom pan, remove gas second cover, loosen nuts on ignitor, cut wires near the ignitor end for extra slack, connect new wire of ignitor, screw on wire caps, reattach ignitor, replace covers and finished. Very easy repair.
After diagnosing the problem, I entered the Tappan Model #, found the part needed, and ordered from Part Select. On receipt (2 day delivery), I followed the instructions enclosed with the ignitor, and within 30 minutes, had everything up and running. Thanks PART SELECT!
open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!
Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.
Install new igniter. You will need to cut existing wires from old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit. Directions are also provided with the new igniter.
I looked up the model number of the Tappan oven on the net, found the part on the PartSelect site, ordered it and it arrived within a few days. The disassembly should have required nothing more than a Phillips head screw driver, unfortunately one of the screws was completely frozen and I managed to strip the Phillips head socket.
The screw was in a very awkward position so I first tried using grip pliers on the edge of the screw - this failed, I then tried grinding a flat spot on either side of the screw circumference and using the flats for gripping - it worked but the screw wouldn't move. Finally, I took a hacksaw blade and cut a slot in the head of the screw. I widened the slot using miniature files and finally made the slot wide enough for a large slot blade screwdriver - this worked. After removing that one screw and maneuvering the broken hinge out of the access hole on the stove front (the break in the hinge was such that this took awhile) the rest of the repair went very quickly.
The oven door was such that I could not see all of the hinge and when the part arrived from PartSelect I thought it was the wrong part. I called your parts return number to ask some questions. The lady who took my call was extremely helpful and we first discussed the part ID, then she showed me how to find a picture of the actual part on your site. After looking at the picture and the diagram I suddenly realized the part was correct - it was just that I thought it was supposed to be installed in a different manner. I'm sorry I didn't remember to get her name because she certainly should be commended for he patience and her assistance. Thanks Again.