Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace the light switch for the refrigerator
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.
Used a screwdriver to remove covers. Used a blow dryer to defrost coil in freezer. Cut zip tie and removed old controller assembly. Inserted new controller assembly and secured with zip tie. It took 24 hours for the fridge to cool completely. Now it works fine.
I called LG and followed the instructions given over the phone. The instructions couldn't have been simpler. Disconnect the appliance for several hours and then connect again. I disconnected the appliance overnight, cleaned out the freezer, and reconnected it. Problem solved. Did not need to call a repairman and did not use the clips.
Refrigerator light had a short in it and would randomly work
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.
unfortunately my fridge stopped working. I purchased another but wanted to try and repair the old one. when ew one arrived, the old one was supposed to be put in garage but instead was hauled away. Had delivery return next day but they had as already removed and lost the handle screw for the bottom freezer and the screw that holds handle in place. ordered the handle screw and picked up the nut. very simple to install the screw and put handle back on.
replaced the ice maker with the new assembly kit, the longest time taken was to fit back the pull out door .. had to align the slots correctly and check that it slid back and forth easily.
Pulled the fridge out of its space. Removed a metal shield which covered the bottom 12" of the fridge with a Philips head screw driver. The water valve is on your right. turned off the water to the supply line. Removed the supply line using an adjustable wrench. Removed the water line gong from the pump into the fridge. It is held on with a "C" clip which can be pulled off with needle-nose pliers. Removed the old pump, held with one Philips head screw. Then installed the new pump, reconnected the lines, replaced the metal shield and turned the water back on. Vacuumed the fridge and its space before cleaning up. The ice-maker now works perfectly.
I removed the broken rail & installed the new rail with a screw driver. The screws were located in somewhat difficult position. The rail works OK but has a tendency to stick & the tray holder sometimes slips out of the new rail.
Door latch (cam) at door top broke off from the gasket holder. Gasket was fine so only needed new holder.
Gasket held in place by plastic bezel. Remove bezel by carefully pulling it toward you. Held in place by plastic clips. May need to pry carefully near clips. Pull gasket away from front edge of door. Gasket holder held by plastic swivel pieces top and bottom. Snap these out. Slide the gasket holder off the gasket. Remove the screws and slip the metal rod out of the broken holder. Retain screws, plastic clips, and cam. Slide the rod into new holder adding plastic clips and cam. Replace screws. Slide holder back onto gasket. Snap plastic clips into slots, being careful to bend the springs back so they go into the channel. Replace bezel. See videos on replacing door gaskets.
Caution removing plastic molding with putty knife or flat bar . Roll the gasket toward the inside of frig ,push old holder up carefully out of gasket. Half way out tilt holder back to avoid ceiling . Save old holder for template ,remove screw from bottom,push out rod ,caution clip is spring loaded, install in new holder in reverse,slide back into gasket(carefully)!!replace molding
The fridge died and couldn't find right parts needed
I was told the mother board went out. Took a few months to finally get one myself after repairman didn't come through. It turned out not to be the motherboard that sears repairman tested it for and said that's what it needed. I found Parts select after going round and round with sears parts refusing to accept return. There prices were better, as well as shipping and it came so quick i thought it was over night. The controller assembly was not the problem so we have it for a spare now. It was the freezer fan but even after installing it nothing would work is why we ordered the controller assembly. after 2 days and about 7 hours of checking, taking apart, rechecking assembling by my determined electrician it turned out to be a loose wire. LOL hope this helps someone. I'm just glad to have my fridge again! Blessings!!!