Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
no power to control panel
really easy to repair... no power to control panel but had power from breaker box. Followed directions that came with part, self explanatory, took 10 mins.
I spent more time reading the easy instructions several times than it took me to actually do the repair to replace the fuse. I wanted to make sure I fully understood the instructions before I undertook the task. I also checked out a video on You-tube which explained and showed me the same thing as the instructions did. By the time I picked up the screwdriver, I was practically "an expert". I just cut two wires and hooked up two new wires and... done. The instructions were simple....so was the repair. Nothing to it.
Removed the old one, cleaned out the groove, dry fit the gasket, made a small cut to fit length, removed, squeezed the glue into the track and then put gasket in. Had to wait 24 hours for glue to cure. No leaks.
Replacement parts from factory installed using u tube support video
Also replaced stop ends for top rack by removing old clip in to push down and lined up to secure in slots at end of rack, notice new plastic parts are installed by pushing hardware into slots downward until they clip into place
Kids loved to make squeaky sounds opening and closing the doors, finally snapped the door balance link on one side.
1) clear out the dishwasher 2) remove unit securing screws from top or sides of DW and cabinetry near the top or under the counter top 3) gently pull the dishwasher from the cabinetry about 20" is plenty, mind the connecting hoses and electrical connection 4) close the door! pull back the insulation from the area of the hinge and photograph both sides - this will save you the pain of going online 5) you will see the cord, the tensioning wheel assembly and the door balance spring on both sides 6) with the door closed to relieve tension on the cord, remove the cord from the balance spring - this can be done w/o tools at this point 7) remove the 5/16" screw from the plastic tensioning wheels and remove the tensioners, cord - leave the springs in place if not replacing them 8) install the door end of the cord to its hook on the hinge, install the new tensioning wheel assembly, install the old 5/16" self tapping screw through the lower wheel and into the outer hole in the frame 9) thread the cord from the door over the upper wheel and lower wheel. the lower wheel has cord retaining tabs to hold the cord on the assembly 10) hook the eye end of the cord to the balance spring and you are finished with the first side - repeat operations for the other side, reposition the insulation and slide the washer back in its cavity - do not forget to reinstall the stabilizing screws in the upper washer frame 11) you've done it! 12) have a cuppa and do your second washer that hasn't failed yet - it will soon.
I closed the water at the tank and opened all the hot water faucets in the house thereby draining static water from the inlet hose at the valve. Then I unscrewed the inlet hose from the valve, unscrewed the valve body from the support bracket under the tub, unplugged the electrical plug from the valve body, and removed the outlet hose. I installed the new valve using the reverse sequence. Then I closed all the hot water faucets, turned on the hot water at the tank, and purged air from each of the faucets. I then started the dishwasher and ran it through a complete cycle, periodically checking it for leaks, and found none. Total time for uninstall and reinstall - about 30 minutes. Not bad for an 80 year old.
Partselect provided me with tracking information for my order, they also provided an installation video. So when I replaced the door seal it was a few minutes to remove the old seal and about five minutes to put in the new one and it was all done.Thanks to Parts select it was a piece a cake
All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,
Follow the u tube instruction. Replacing the pump was very simple and easy. The hard part was getting the dishwasher out of the cabinet and back in again.
Note orientation of the old gasket before removing it, so you can put the new one in right. Pull the old one out, which is a snap. Mark the center of the new one and push the center into the channel with your thumb nail at the top middle of the machine. Continue pushing it in on both sides, from top to bottom, in a steady, fluid motion; don't stretch it. If there is a bit extra at the ends, cut it off with a scissors, being conservative so you don't cut it too short. The new gasket will make the door a bit harder to close, but that's what you want.
A mouse was chewed through the hose and ate part of it. Di
Disconnected the damaged hose extension from the dishwasher outlet drain hose and the connection to the sink drain. Removed two clamps. One a spring clamp and the other a screw clamps. Connected the new extension hose with a spring clamp to the dishwasher outlet drain hose. Connected the other end to the sink drain with a screw clamp. Checked for leaks. Good to go!
drain pump noisy, broken piece of glass caught in pump.
removed kick panel with screwdriver, 90 degree turn of screw. Put towel under drain pump. Disconnect drain hose by loosening spring clip with pliers to provide access to pump. released spring clip on old motor while turning counterclockwise to separate pump from drain reservoir. inspect drain reservoir from inside machine to remove any foreign objects. Installed new pump by indexing attachment flanges to notches in reservoir and turning pump clockwise until locking tab makes audible click. reattach drain hose insuring hose is contacting "stop" ribs on drain hose pipe. Run wash cycle on machine to insure there are no leaks. Re-attached kick panel.
12 screws remove door outside panel unplug wire remove 6 mounting screw remove old unit put new unit in place put 6 small mounting screws back plug wire in put front door panel in place put 12 door screws in your done now you can start and test run
