Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
the door bins failed rather quicklyAn unknown white substance was observed down the side of the door at the juncture of the bin and the edge of the door/hinge side
we removed the old broken bins and replaced with new door bins
Took off refrigerator door from top hinge and lifted off. A little difficulty getting worn out parts off (needed dremel to drill out worn plastic); replaced with new parts, the screw head holding on the part was starting to be worn as well but still worked. If I hadn't got to this repair soon the bottom of the door aluminum would have total worn out as it is, it has a deep groove but not noticeable. The new cams also force the door closed tight instead of slightly ajar at times.
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
First, I replaced the auger motor at a cost of $87.00. That job took about 15 minutes and was very easy, but it still didn't work. So, I took off the front panel that covered the ice/water dispenser controls and some white plastic parts rained down out of it. I then discovered the problem was the mounting points that held the ice dispenser switch in place. The $13.00 white control bracket fixed the problem. Should have checked this first, as I later learned that the motors rarely go bad.
1. Unplugged refrigerator. 2. Emptied Freezer. 3. Removed Ice Maker. 4. Waited a few hours for ice to melt around back panel & nuts. 5. Removed back panel and the cover over fan and fan motor. 6. Waited many more hours for ice to thaw over fins, wiring, etc. 7. Easily replaced the bi-mental defrost thermostat. 8. Replaced panel, fan cover, ice maker. 9. Plugged in refrigerator and waited a bit.
This worked! Yahoo.
p.s. I am a 65+ year old mechanically minded woman. :-)
Part would not fit straight in. Used universal joint on end of extension to reach screw rather that disassemble front. Managed to slip the paddel just far enough to one side and angled to snap ice guid on and then slipped paddel back into place. Used a dab of candle stickum on the screw head to heep it in the socket and then inserted in door. $7 part, 15min and saved $$$$$$ over a service call;)
Ice Maker would no longer move ice through the dispenser
As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.
Door Chute Mechanism broke / air flow into ice maker
Have not installed yet as I'm on a quick TX-FL-TX turnaround. Bought and received the part in 24 hours...great. Order contained no instructions. I could probably figure it out myself just have not attempted yet.