Enter the code USA15 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on July 1 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Rats/Mice chewed wiring - valves frozen
There was no wiring harness available so we removed the block and connected all wires (with some additional wire due to the chewing). After all that, the repair went quite well. Parts arrived in about 3 days....everything's back up and running. Thanks again for your help and prompt service! Carol
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
6 of 18 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light keep burning out in oven.
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid door back on and done. 30 minutes at most.
Deflector oven/gas flame deflector replaced due to hole melted from glowbar igniter
Removed oven convection fan cover for more room to remove/replace lower oven bottom. Deflector is attached underneath oven bottom and you will need new self tapping sheet metal screws to replace old ones. My deflector actually had hole melted in it from glowbar igniter directly underneath it. Glowbar remains white hot until selected oven temp is reached...poorly designed.
Slide out oven door. Remove handle screw and handle. Pick up white insulation. Remove screws to the door gasket. Replace new Door Gasket. It had to te streched to fit. I wish that the new door gasket would be 2 in. longer so it would be easier to install.
Installation was very quick and simple. Removed wire connector for the igniter then hex screws for the bake tube. Attached the new igniter to the new bake tube and reinstalled in oven. 15 mins. I took the extra time to clean the oven pan and heat shields. Removed old charred baking spills and grease buildup. Oven is 12 years old and working like brand new.
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Wall oven: light flickered or did not work in a loose poreclain socket.
Shut off power at the panel to the electric oven. Removed 2 phillips screws holding bulb unit in place in the top of teh oven chamber. One wire was so frayed it came out of the push on connector. Stripped off insulation and reinstalled onto the connector, using pliers to snug the wires down. Installed the new porcelain socket from Parts Select, replaced the unit in the top of the oven unit. Installed a new bulb, then snapped the new glass housing into place with the existing retaining wire clip. Presto: works like it's brand new. Thanks to Parts Select for the right parts, and for such quick delivery. I will use them again!
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
stove converted to propane. 2 year later a bad oder developed.
called appliance repairman. He found problem and ordered new part. After 2 months waiting for part to get there, my husband got on internet and calld your number, and ordered what was needed. Now for the great thing. Within 4 working days we received what we thought we needed. but we had ordered the wrong part number. Got back on internet, went right to your web site, found the part that we did need, a flame spreader instead of the Deflector. called your service number, talked to a very nice person, again, told her what we did and ordered the correct part. Another great thing, we got that part the very next day. I returned the wrong part that same day. We then had our son install it and now we have a very nice working oven. Though out this very long ordeal, we talked to the applicance service people and got the same answer. The part has been ordered and it should be here next week. When we found your web site and called for the part, I called the appliance service and told them we had ordered the part ourselves and I would be happy to give her this information. THE VERY NEXT DAY she called us to tell us the part had fially arrived and they could come out the next day. Told them sorry but it as already taken care of. The very next time we need some part for any appliance we will call you first. Thank you for your very nice service people and the fast way that this all took place.
Replaced the burner and igniter after watching the repair video provided by Partselect. I was pleasantly surprised when the parts came the very next day. It was so easy and the igniter plug matched perfect. My wife wanted to hire a repair man but I did the repair and saved a bundle on the labor. I couldn't be happier about my purchase.
Oven would fill up with gas before igniter got hot enough to lite it
Remove bottom drawer,open oven door,take oven racks out,use flat tip screwdriver to remove two screws in back of oven. Then remove cover over burner and igniter.Reach under oven and unplug igniter,while down there use 1/4 inch nut driver and remove two screws holding burner. Then remove one screw inside oven in front of burner. Pull burner and igniter up and out of oven.I did not unplug stove or turn off gas some people may want to,if you have to move stove out to work on it