Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven igniter didn't work.
The bolts were below the base of the oven, and very difficult to remove and replace. The directions were not applicable to our unit. The good news was the igniter was correct, even though we had to adapt the bracket.
the instructions given for this part were not 100 % accurate, our oven door required multiple, dis assembly and was unable to complete the task, local handy men refused to come to assist since the job was already started, it appears I will now need to buy a new oven , I was disapointed in the help because had we known we had the more diffcilult oven, would not have attempted, I did give the correct model and serial number to the person when discussing this part
You need to remove the knobs and remove the panel where the knobs are connected.
You also need to remove the display panel front to gain access to the where the electrode wires attach.
The other screws are readily visible. It's about 30 screws that need to be pulled.
The adapter put on the electrode can be pulled off with needle nose pliers and a small screwdriver, if the adapter does not fit through the opening on your stove. Just put the adapter back on after you snake the wires through.
1) Verified it was the broiler igniter that was damaged. 2) Removed the oven door, the lower pot storage drawer and the top range panel. 3) Turned off the gas supply in the top range area. Pulled the electrical plug-in out of the lower electrical panel (behind the lower drawer). 4) Used the nut driver to remove the two (2) 1/4" screws that held the igniter to the back wall of the oven. I later read in the Use & Care Guide that this is easier to do if the broiler burner cover is removed first. 5) I pulled the damaged igniter away from the back wall, expecting to expose wire connectors or splicing but was only able to get about 6" of the two (2) insulated wires before I could not pull them any further. 6) Therefore, I cut the wires and, without a proper wire stripper, cut about 3/8" of insulation away in order to make a splice between the wiring from the new igniter and the wiring coming out of the back of the oven. Big mistake ..... do not recommend this without using a proper wire stripper! I must have cut into the existing exposed oven wiring on one of the wires such that when I used the twist-on to make the splice, most of the wires (those wound together to form one wire) were damaged and broke away. Unfortuantely I did not find this out until everything was put back together and we (my wife and I) did the test. No results! 7) I took everything apart again and when I tried to pull the wiring back out from in behind the oven wall, one wire came out with the twist-on in tact and the other came out "with no wire attachment". 8) I now had to figure out how to get into the back of the oven to retrieve the "lost connecting wire". It is quite simple when you know what you are doing but no instructions (that I had) advised that the upper back light gauge metal panels could be easily removed to expose the wiring. This was eventually determined and the connections were both made again in a more positive manner. 9) We (my wife and I) put it all back together and this time it was fine ..... just had to be patient while the gas purged the air out of the broiler burner line. 10) Lessons learned: GE made it easy "once you knew how it could be done". I suspect GE feels that service type people should be doing these things but with a 120VAC (vs higher voltage electric type ovens) system why not provide the info for the "do-it-yourselfers" as well?
I removed the broken glass and scraped the edges to remove any excess. Then I slipped in the new glass and used the hammer to bend back the edge that holds the glass in place. Your company and website made it very easy for me to find and order the part I needed to repair my oven. Also, I saved about $30 compared to the quote I received from my local appliance store.
I took all of the oven racks out , then the bottom cover, over the element. I immediately saw the igniter coil was broken. I took the element out and disconnected the two wires. (I saw that the igniter coil was broken and knew that must be my problem. I got my manual out and found the part number and got on line and started shopping. I found part select, the price was fair and ordered it the same day. It was shipped out to me the same day I ordered it. Received it the next day and had the oven working again. Easy to order, great customer service, fast shipping department. Great job to all of you folks at Part Select. I would recommend PS to anyone that wants to save money and do it yourself. Go for it. tk middlebury IN.
Took it out of the box, lifted the stove lid and replaced the part, no tools required. Very satisfied with the shipping and the part, great service. Thanks!
• Start by unplugging the unit from the wall. • Then slide the unit out carefully without damaging the gas line. • Next remove the lower drawer just under the stove. Pull all of the way out then lift slightly and continue pulling gently. The drawer should slide out with no need for tools. • Tilt the range backwards towards the wall allowing enough room to access the back of the range where the gas control is. • Remove the sheet metal under the stove. There should only be four hex head sheet metal screw holding it in place. • Look at the gas control, and follow the white wires going up this should show you where the lower igniter for the oven is. • Remove the igniter 1-2 screws • Check to make sure you have the correct igniter. The upper and lower are the same. ****The label where my serial # is says that the unit only uses 5 amp igniters however the igniter I pulled out said 2-3 amp… fortunately Parts Select sent me the correct igniter without me knowing the difference when I ordered**** • Replace the old igniter with the new and wire it in per the instructions. **** I had to use butt connectors and part of the old wire because the replacement did not come with the correct connectors to attach to the gas control. It should be ok since it is only 5 amps and under**** • Reassemble the range and replace the drawer. • Be careful when putting the range back in its place, not to tear the linoleum. I wet down the floor with glass cleaner to make it slick.
Good luck, I may have had it done in less than half an hour but I have a two and a half year old who must help daddy do it all. Takes longer but makes it more fun… Brad.
Oven would not work. Burners worked fine. Igniter would not glow.
It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.
First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven. PartSelect makes repairs quick & easy. It just takes a little smarts on your part.
oven would not come on.igniter has to light for oven to come on
well first off I repair commercial HVAC equipment for a major drug company so I think I've done it all.I thought it cant be much different than any burner assembly.I made it harder than it had to be,anyone can do this.I removed lots of unneccessary things.Let me help you only take out the drawer on bottom of stove.so I started on top and worked my way down.save time and open the stove to were the door stops then have faith and give a good yank.this will remove the door,dont be afraid it will go right back on those two hinges easy.now that this is out of the way remove the bottom plate that covers the burner assembly (2 screws)in back pull it out then you see the igniter.as I said before with drawer pulled out remove the 2 1/4"nuts screws holding it up then from bottom.Unplug this stove then remove the 2 places its plugged in to.after you remove this there are 2 screws that hold it into the igniter remove them .cut the wires with enough room to re use the plug ends.strip the wires and use the wire nuts that they provide then put back together with new wires on new igniter then.re attach.put everything back together in the reverse order you took them apart.plug in stove and see the igniter light up again and light stove.do not call repairman you can do this.save your money for you its bad enough you have to buy anything else.
I rempved the top and bottom doors, than the wire rackes followed by the bottom base of the oven. Then I removed the burner cover plate so I could get to the igniter.. I removed the cover plate for the wiring (2 wires), unpluged them, removed the igniter (2 screws). I had to cut the wires on the old igniter and couple the ends to the new igniter and then replaced everything by just reversing all that I did. Simple! Easy!
- removed the oven unit from the wall - removed the aluminum backplate to expose the wiring - Removed both glass wire nuts and disconnected the heating element\ - From the front, I removed both retainer screws and pulled the element wires through. - In reverse order I reinsalled the new wires and screwed on the heating element. -I reattached the electrical wiring and rear pane. - I re-installed the unit into the wall.
