The fridge lower hinge mechanism which assists door closing broke
Removed the top hinge cover with Philips screwdriver. Removed the three bolts holding the top hinge in place. Removed the top hinge, and lifted the door off the remains of the lower hinge. Unbolted the remnants of the lower hinge closure mechanism and replaced it with the new set. Reassembled the door on the lower hinge, and then replaced and bolted back on the top hinge. Door back to full working order in less than fifteen minutes.
Broken freezer door cam and leaking freezer door gasket
First I pulled the fridge out from the wall and turned off the water supply. Next I removed the access panel on the bottom front of the fridge. Located behind the panel was the water supply line for the water dispenser in the door which has a disconnect the I simply unscrewed so that I would be able to lift the door off of the bottom hinge. Next I took one screw out of the top hinge cover to access three small bolts and disconnect the electrical connections to the door. After removing the bolts I lifted the door off and took out the small screw holding in the bottom cam and replaced with the new one. After reinstalling door I removed all the small bolts holding on the freezer gasket. After this the gasket easily pulls out and began installing the new gasket. This part of the job was the most time consuming. After I had the gasket back behind the pinch rail I began reinstalling the bolts. Since the gasket was bent during shipping I simply took a hair dryer to the slightly bent parts of the gasket to get them to lay flat. Freezer now has a great seal and stays closed when refrigerator door is being shut.
Replaced dorr closure cam on both doors of side-by-side
The fridge door was easy. Just unscrew top and lift off hindge. The freezer door took longer. But I had the user guide which helped. We unhooked the power harness at the top of the door, and disconnected the water line at the bottom of the door.
Frankly, it wasn't that hard for me because I had my son-in-law do it!
The right door was sagging and the handles were rubbing together
First, remove the plastic cover off the top hinge by removing the single phillips head screw.
Removed the three hex-head screws holding the hinge to the body of the fridge and then lift the hinge off of the door.
Lift the door off the bottom hinge and place on a flat surface so you can easily access the bottom.
Remove the single hex-head screw from the center of the door part of the closure cam and pull it free. Install the new part.
Next, remove the bottom portion of the closure cam from the lower door hinge (still attached to the fridge) by removing the single hex-head screw. Install the new part.
If needed, lube the lower door hinge with Vaseline and carefully set the door back on. (This is the hard part if you are working alone, as it can be hard to line up the hole.)
Lube the top hinge, reinstall, and replace the plastic cover. Easy as 1, 2, 3.
Plastic Cams on frig door cracked in halk/door wouldn't close easily
Removed the top hinge (4 screws)-lifted the door off of the lower hinge-replaced both halves of the cam kit and mounted the door and reattached the upper hinge. Probably took about fifteen minutes total.
Remove the grandkids pictures from the door then empty the contents inside the door. Remove the top hinge cover and the top hinge bracket. Lift the door off the bottom pivot. Replace the lower cam by removing one screw. With the door in the horizontal position, remove and replace the upper cam. Apply a little grease on both cam surfaces. Align the door before tightening the top bracket and your done. If you did not take a picture of the door before you started the project you will have to rely on memory to arrange the pictures in the proper location.
The worst part was unloading the door shelves. Removed upper hinge cover and hinge hex screws. This allows the door to be removed. Lay the door on side. Remove screw that holds cam in place. Replace broken cam with new piece. Put the door back on the hinge pin and replace upper hinge screws and cover. Now reload all of the stuff.
Main door was making a thunping noise when opened.
Took the door off, and replaced the plastic shim on the bottom that was the cause of the problem. The shim had broken into pieces and was no longer holding the door in height and alignment. I was proud of myself that I could repair it myself and avoid a $125.00 service call from a repairman. Total cost of repair including shipping and handling was just south of $12.00.
I followed the other web notes with one change .Since I too forgot the lube , I used a pry bar and block of wood to lift the door and a tooth pick to glob some lube in the lower hinge.
I watched the online video and followed the directions. The only thing that was not obvious (and this is where the video saved several minutes)was how to remove the upper part from the door. This repair makes the door seals much more effective and should reduce the compressor run time. I have to compliment you on your prices and speed in getting the parts to me...great service!
First My Frig side of the double door unit wasn't closing on its own. Kids don't look, so they walk away...next thing you know the frig warms up and the freezer starts to frost up from running so long...Now it won't shut off.... I checked the hinge and sure enough it was wore down. Now mind you, I ordered a hinge kit first without checking to see what type I needed...don't do that...Less than 15 mins you can take the door off and see which one you need.As soon as I saw which type of hinge set I needed I went and ordered it...returned the other one. It came pretty quick.... 15 mins had that sucker changed and working... But... the door still wouldn't close on its own... Common sense told me the heat from the frosted freezer caused the door and frig walls to swell... Yes I said the heat... When the component in the freezer frosts up it does not keep the frig cool, nor will the freezer stay kool... the frost prevents the cool air from moving around...thus "HEAT".... It took a full 24 hrs for my frig n freezer to get back to normal... and now the door closes just fine... MIND YOU! I had to take the covers off the freezer unit inside, then take a steamer and melt all that frost off of every inch including down the drain... That took me a good 5-6 hours... and what a mess.... but it was worth my time.... because I don't have to replace my second hand Jenn-Air which I could never afford to buy brand new.... Whew....what we have to do to keep things going... $11 bucks worth of parts.... "Super Mom" :o)
