per the video..easy installation....unfortunately the temperature did not improve. We still have a refrigerator temp in the upper freezer.....and a "cooler" in the refrigerator section
Removed bottom cover , just two screws , slid old part through install hole and removed wires from old switch and installed on new switch. Installed new switch in same hole and pushed gently until it locked in place. Reinstalled bottom cover and done.
I should have ordered start kit instead of start capacitor. The start cap astir did not fix problem so I ordered kit. Compasator comes as part of kit. Followed enclosed instructions. Cut existing wires and reconnected new wiring. Simple as that. It's a plug in item. Now worried it may be working to good. Freezer down to 10 deg. Watching to see if compressor is running to long. Seems ok lol. Wife hates me now. She wanted new frige.
The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.
Removed 2 screws holding front bottom vent grille. . Through opening behind grille found broken part of switch hanging on wires. Removed wires from switch and fed them out through hole for mounting switch, connected wire and pushed into place. The greatest difficulty encountered was my 82 year old knees.
I replaced the defrost timer,defrost thermostat,and run cap.as it turned out the compressor went bad. I dont know the model because but the time I got this review I replaced the refer with a knew one . two weeks living out of coolers was so much fun !!!!!!!!
I replaced the thermostat. (Note: On a chest freezer, there is a copper tube going up into the wall of the freezer. The capillary of the thermostat goes into this tube.) 1. Unplug freezer. 2. Remove temperature knob. 3. Remove screws and remove cover plate. 4. Unclip old thermostat. 5. Using pliers, gently pull down the rubber seal on the capillary where it enters the copper tube. 6. Pull capillary out of copper tube. (In my case, the capillary was not free to pull out. I had to grasp the capillary with pliers and tug hard.) 7. Place rubber seal over the new capillary. 8. Insert the new capillary into the copper tube and put the rubber seal over the end of the copper tube. 9. Install thermostat body in the cover plate using the clip on the thermostat body. 10. Replace cover plate and temperature knob.
it was great. I ordered the capacitor for my frigidaire frig and it arrived in 3 days. plugged in the part to the compressor and my frig has been working ever since. I spent 3 minutes ordering the part and 30 seconds attaching it to the frig. Easy, very easy. saved myself a 75 dollar repair visit. thanks
Since everything about the freezer was working, I decided it had to be the temperature control. I ordered the part from Parts Select on a Monday and it arrived on Tuesday. I removed the two screws that hold the panel that covers the parts. The control was right there. Two more screws and it was out. Reverse the operation to install the new part and just like that in less than 5 minutes my freezer was running like new.
After reading reviews I was not sure but I ordered part on Wensday in the AM and I had the correct part Thursday evening this company rocks thank you by the way i paid for regular shipping I will order again in a heartbeat
thanks to all of the people who had the same problems I was able to make a quick fix on my fridge. I pulled the back cover off and found the compressor not kicking on so I replaced the start cap. and im back in bussiness.
