Water filter would not disconnect from OEM Water Filter Base
Disconnect the two water supply tubes at the base of the Water Filter Base. Using a 7/16" open end wrench, press up on the blue "O" rings to disconnect the tubes. Use a Using an 8" long magnetic phillips head screw driver I was able to unscrew the 4 short screws holding the original water filter base and the immovable attached water filter. Replacement was easy. Simply slide the new base into the fixed slot on the refrigerator and reinstall the 4 holding screws. Reconnect the water supply tubes to the Water Filter Base. Install a new water filter.
Not making ice and leaking water from aebecause the icemold in the ice maker cracked
Removed the trough that catches the ice.. two philips screws to take the front cover off. Side and bottom. Than quarter inch to remove cover over wires. Unplug ones to ice maker. Slide out a little and down. May be a zip tie in the back cut with sheet rock knife. Reverse to install.
First: I could not watch any videos. Big downer. Read the reviews and read a post about “three screws”. Opened the freezer and emptied everything in it. Remove the bin. Two screws are on the left side. They go into the side wall. Here’s where things get weird. The plastic “box” holds the “ice making assembly”. That box is attached by FOUR slots. You will need to remove the wire rack below the frame. There’s a plastic spacer on the left side with a slot on it. You can pull it of with your fingers when you rotate it. Slide the rack to the left and pull down the rack from the RIGHT side holes. You have move the box toward you about a inch, then it drops down. Now, there is a electrical connection from the box to the rear of the refrigerator wall. You need a small screwdriver to lift the tab on the TOP of the connector to release it. Once that is done, slide the box forward and put it in the sink. While all this is happening, the freezer is thawing out. Once you remove the box, you will get error codes on the digital display. This is a good thing. There are two “square head’” screws that you have to remove to separate the TWO parts that make the box. Slide the outer trim towards you. The icemaker assembly slides into four slots. You put the new wires in the same place as the one you removed. Put everything back together the opposite of the removal. Now for the secret. All that food you removed? Put it back in until you can slide the box into place. Then you plug the connector in. The box should be sitting on the food. THIS IS THE SECRET. The ice maker has two options. Cubed or Crushed. There are two components that make them happen. On the left side there is a slot with a gray lever the moves up an down. There is an piece of aluminum on the right side the drives the screw in the box. Rotate the screw drive to 45 degrees. THIS IS THE SECRET. On the left side of the box is a rod that is spring loaded and has a bent end. It’s about “timing”. Find a piece of “kite string”. I used the string from the yellow energy tag that came with the fridge. The box is sitting on the frozen food. The wire in the back is connected. Loop the string around the lever AND PULL UP. Slide the whole thing into place using the slots. When it’s in place, let go of the string. Put the two screws back in.
FINAL. You have to PRESS AND HOLD the IceMaker button to reset. You’ll get ice cubes in a couple of hours. Through the first 24 hrs away. You’re welcom.
The left side roller broke away from the crisper cover frame
I removed and separated the crisper tray and cover from the refrigerator. Removed the left side rail from the damaged cover and discarded the old cover. I added the new roller to the new cover and replaced the side rail to the new cover and reassembled into the refrigerator
The roller wheel is part of the shelf that acts as a topper to the draw and not part of the are that supports the shelf. Removing the shelf and using a Phillips screw driver, I removed the right and left arms from the shelf along with remaining wheels. Re-attaching the arms and all the wheels, I placed the shelf back on the slotted rail and inserted the crisper draw.
There is no power, due to the COVID-19 pandemic there no Tech support available,
My repair plan is to continue buying parts for it until is starts working. I notices a large rusty stain on the back of the refrigerator, so I replaced the Ice Maker. Then, I replaced the Evaporator Motor. Yet nothing will come on. I called Conn's Home Plus where I bought the Frigidaire Refigerator back in February 2014. The Tech said that It needs a Board-main Power (computer part). So I it ordered from PartSelect. It is due here by July 20, 2020. The Parts and Tech cost is now over Five Hundred ($500) dollars. HELP!! I need INSTRUCTIONS, HELP!!! Albert F. Alfaro in San Antonio, TX.
I did not do a repair. You sent the wrong part & I didn't open the package but I can't get hold of anyone to return the part and get the correct part.
I am very upset that no one will help me. I paid $ 37.28 for the part I ordered and then the wrong part was sent
The sku # on the package is 242010901.This is a roller type part and I ordered a small wheel. I can't even find a return address to send it to.. Please help me Elizabeth Romage libbieinrichmond@comcast.net 8042627963
Fridge started making a loud racket. Condenser Fan Blade then disintegrated to dust and pieces. The plastic had degraded significantly.
The repair itself total time was quick and easy. Since the original fan blade blew apart, it was only a matter of putting the new one on in it's place. This can be done by feeding the blade between the cowling and Condenser coil and applying pressure to get it on the shaft.
If your fan is still on the shaft, simply push it off and extract it the same way. Then place the new one on the shaft.
In my case, since the part would take a couple days to get, and I had food both in the fridge and the freezer, I removed and unplugged the Condenser Fan Motor and the cowling frame and temporarily spliced a small fan I had into the line for the condenser motor. This kept the fridge working long enough to get the replacement part.
Side note. Direction of airflow is towards the Compressor, and draws air across the Condenser coils.
Did not repair, sensor was not located where you said, wrong sensor was sent to me, can't return oe exchange it COSTERMER SERVICE WILL NOT ANSWER MY EMAILS.
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker. 2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,. 3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket. 4.Now take out 8 screws that hold the back panel in place and remove the back panel. 5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
i put casket on i notice when i received casket in shipping box was bent on the end of the casket 's did not solve problem casket not flush air is due to damage from shipping in the box not happy with the product.