Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water was dispensing slowly through water line.
I followed all the usual suggestions about changing the water filter and disconnecting the exterior copper line and testing it to make sure flow was steady. I then got ambitious and diconnected and tested the flow of water through each of the refrigerator's interior valves. Isolating my problem inside the dual valve that regulates feed into the water dispenser and icemaker I was able to clear out the blockage with a small dustbuster air cannister but reassmbling the valves somehow caused the valve to no longer function right so I ordered a replacement valve and had it all reconnected in five minutes once the part arrived. A simple repair to avoid a very costly replacement! Partselect has now been used by me to repair my oven, refrigerator (twice) and microwave. A pretty good alternative to replacing an appliance if you are willing to try your own repair.
Ordered parts, and replaced them. Living in Alaska it made the shipping take a little longer but they arrived and now the top hinge dosen't pop out, door shuts nicley and we were able to turn the temp. control down which in the long run will save electricity.
I order part # PS429001 dual inlet water valve located in bottom left corner of refridge on monday it arrived nest day.I then shut off water source and disconnected refridge. I removed back bottom panel { 5screws} and then i removed water valve {1 screw} I unplugged electrical wires and water feed lines from valve.You have to pull hard on feed lines to remove. I installed new valve, connected wires, i had to clip off about 1/2" of feed line ends for a tighter fit on new valve. I reinstalled back panel. I plugged in refridge turned on water,and presto i'm getting fast water again from the dispenser. P.S. I also took the time to vacumm around compressor and fan. thanks PARTSELECT.
Turned off water and unplugged refrigerator. Removed rear cardboard pannel. Removed screw holding valve, unscrewed water lines, disconnected wires. Drained excess water into cup. Reinstalled lines on new valve. Reconnected wires. Installed into place. Reinstalled cover. Done. Wasn't sure if this was the problem but narrowed it down to a few things. Valve wasn't closing all of the way allowing water to continue to drip into ice maker and out door. Works perfectly. Oreder on Sunday received by Tuesday. No complaints for PartsSelect.
The longest part of replacing the drawer was swapping all the veggies out of the old one. No tools,slid the glass drawer front from the old one and slid it into the new one.
Wasn't sure if it was the derost timer or the heating element. Since the timer was much cheaper, I bought it and crossed my fingers. My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring. Success! My coils no longer freeze up. Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.
the heater defroster was bad. tested and no continuity brake in eliment.just doing a visual might have detected it but it`s hidden behind the coils.....all is working now
Frequent dripping on floor and no cycling of compressor
After posting the specific symptoms and getting feedback, I had narrowed the cause to two linked parts. I ordered both intending to replace first one, then the other as needed. With parts in hand, I pulled off the freezer control knob, used a nut driver to remove the two panel securing screws (behind the face, against the inner ceiling) and gently dropped the cover down. The control (temp sensor and cold control) is easily accessible as it sits wedged into two slots in the plastic cover. The control must be slightly lifted in order to extract the long sensor that attaches to the control and runs under it and into a plastic sleeve behind the panel (the new control comes with the sensor wrapped in a tight coil and it must be unwound for the install). Removed the three wires noting which color goes where. Used needle-nose pliers to remove the small push-on tabs and removed the control. After starting the new sensor probe into the sleeve re-attached the 3 wires to the new control. Used the original as a model for how to pre-bend the probe for the first 2 inches as it was mildly frustrating to position the unit back correctly. Pushed everything back into place, re-installed the screws and plugged the fridge back in...(you DID unplug it first, right?). Still haven't used the second part (defrost timer), but I expect it to go soon...it is a 17 year old refrigerator, after all.
Pull refrigerator from wall and disconnect the water line and unplug the power.
On top of the icemaker, two machine screws hold the icemaker to the side of the refrigerator. You will have to feel around to find the machine screws, but once you do, it is simple to slip the appropriate size socket over the hex heads. I found it helpful to have an extension on the socket wrench. Disconnect the power cable inside the refrigerator (there are little pressure clips on the side that help release the cable) and move it out of the way for the time-being.
Back out both machine screws several turns, but do not remove them completely. The icemaker slips over the screws, so leaving them in the side of the refrigerator makes that process a lot easier. Hand tighten the machine screws once you have positioned the new icemaker in place. One thing to be sure and do is make sure the water line hose coming out of the back of the refrigerator inside is on top of the icemaker. It fits into a slot in the top of the icemaker - failing to do this will result in water pouring into the freezer compartment, not into the icemaker..
Reconnect the power cable to the new icemaker and tuck it up behind the icemaker assembly. Tighten the machine screws completely, but do not over-tighten.
Reconnect the water line on the back of the refrigerator at the wall, and plug in the refrigerator. You should hear the unit fill immediately.
In about an hour you should have ice filling the bin. Enjoy!
I removed the old ice maker and unplugged the cable. Screwed in the new one with a 1/4 nut driver at the 2 mounting screws, plugged cable in. Checked ice maker with a small level before final. All Ok and after night I had Ice and it has been working great since.
I removed the two screws and unplugged it. I then attached the pigtail to the appliance, then to the fridge. I had to push the excess wire harness into the hole in the back. It took a few minutes to move the rest of the harness out of the way by curving it upward and securing it with a nylon tie.I ordered the ice maker from Part Select on Sunday night and it arrived at 8:32 Tuesday morning, THANK YOU! I ordered very simple weed cutter parts from Sears a week ago and they haven't even shipped yet!
Freezer was getting a build up of frost on the condenser and wasn't cooling.
First I remove the back panel which had 4 screws. Then I removed the ice maker. The icemaker is held in place by the 2 screws that requires backing the screws out just a litter, than lift up and remove the electrical connector. Used a volt ohm meter to check the resisitant in the heater element and the defrost timing switch. Both tested good and that left only the thermostat. Removed and replaced the thermastat swich. I cut the ends of the old switch and crimp the ends of wire with the crimps that came with the swict i purchased from parts select. My refrigerator is working properly and making ice like normal.
I unscrewed the cover, took out old filter, put in new filter and replaced cover. End of story. Oh...don't forget to turn off the incoming water supply.
