Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Right front burner would only stay on high
Turned off breaker, pulled stove from wall, took off knob, unscrewed and pull off backing from stove, unscrewed heat control part, unplugged wires, plugged into new part, installed part, replaced stove backing, replaced knob, pushed stove back in place and turned on breaker. It worked fine.
I installed the new switch. No difference. I switched elements with the other 8”. Same thing. I called Part Select and their rep said he doubted the new switch was defective but if it was they would replace it. But first how about trading the new switch with the other 8” switch that is working. I did that and the new switch worked fine on that burner but the old switch that worked before allowed the bad burner to go to red hot. Now I’m at a loss. All I see is a new stove. I don’t know what to do next and am open to any and all suggestions.
Unplug from outlet and top remove back section of range and unplug wiring from switch, remove knob and unscrew two screws and remove old switch. Install new switch reinstall screws and plug switch plugs into new switch (will only go on the correct way). reattach back and plug into outlet. All done and surface element works perfectly.
Lower oven Igniter wouldn't heat up and fire the propane.
Called repair man and described the problem. He said I could do it myself. PartSelect had the part and a previous description on the PartSelect site told me how to do the repair. It was easy. Be careful when removing the igniter nuts. I used a very small amount of sewing machine oil so as not to strip the threads. works great.
This burner on our range had no temperature control - it was either full-on or full-off
1. Pull range out from wall 2. Unplug range 3. Remove back cover using drill and screwdriver bit 4. Remove dial handle on affected burner dial 5. Remove two screws to unattach broken infinite switch 6. Disconnect wires from broken infinite switch 7. Reconnect wires to new infinite switch 8. Attach new infinite switch using two screws 9. Use pliers to snap off end of post to fit your burner dial, if necessary. It was on ours. 10. Reconnnect dial handle. 11. Reattach back cover using drill and screwdriver bit. 12. Plug range back in 13. Relocate stove against wall
this was so simple.. attach with 2 screws and plug in and done.. less than a minute.. to be honest it took me longer to put the oven back together than installing the new part. lol
F2 error code when oven was set at a higher temperature.
I pretty much followed the youtube video posted under the part that I needed. Turned off electricity to that area of the house. Unplugged stove. Took out the old sensor, pushed new sensor cord through the back hole. I did put a small amount of tape,so I could pull it through from the back better. It was impossible to get the clip disconnected in the back and the new clip didn't match up correctly anyway. Ended up having to cut the wires and strip them. I twisted them together and put on the ceramic wire nuts on. Reversed ever thing I did and F3 appeared. Looked that code up on internet. It was from an open or shorted oven. Suggested I check the connections. Pulled stove out again, unscrewed caps on wires and noticed the sensor's wire had another cloth type coating on it. I gentle cut that off, twisted and capped wires again. Plugged in oven, turn on electricity, and tried out stove. Everything is working just fine. Everything took a little longer because this was first time doing this type of repair.
Thank goodness for PartSelect.com When we moved into our home the microwave and electric range are obsolete appliances and were missing parts. PartSelect.com has pictures of parts on one inch grid pattern so I was able to select the hard to find parts that would fit perfectly and they did.
ordered parts and disassembled old burners and installed new ones. All the parts were in the box when delivered. Helping my 80 yr old mother-in-law very happy.
Got parts in for one of her 81st birthday present she was thrilled.
