Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Door catch on dryer door broke
PartSelect sent me three different door catches with instructions for choosing the correct one. I did choose and simply inserted it into the slot and voile! All finished and it works great now! PartSelect had the part delivered the day after my order was placed. I would suggest doing business with them to anyone asking who they might contact for a part. I especially appreciated the ease of identifying and ordering from them. I was able to do all of this on-line via their website.
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor. Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaft they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I am 80 years old). Your video is great. Gives step by step instructions.
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
squeaking sound due to worn out bearing idler pulley wheel.
BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut screws of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.
Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy as the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.
When using the dryer the cycle would stop and display E1 as the reason
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
I typed in on my brouser Repair Kitchen Aid Dryer door switch. And on You Tube up came several videos showing me how to ewmove the switch and install the new one.
The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away from the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada